I am comletely new to lighting...

I purchased an elation DMX operator pro, with 2 ADJ acuspot 250II, 8 par cans, and 2 dp-dmx20L.

I hooked a few things together so i could get the hang of it. From the dmx console to 1 250II, to the next 250II, then to the dimmer pack witch for now is connecting 2 par cans. i set the first address of the first 250II as A001, and the second 250II as A017, and then the dimmer pack as A129.

I would like to know if it's possible to breakup the dimmer packs channels onto different faders. so on the dimmer pack, i would like fader 129 bbring up channel 1 lights, and then 130 bring up channel 2 lights, and so on... 1 is that possible, and 2 how would i do it?


Also is there a way to have 1 of the 250II mirror the other 250II. so i would place 1 250II in front of the runway(to the left), and the other 250II in front of the runway (to the right){[ i was planing on usin this equipment for a fashionshow]}

How would i go about this(FYI: the gig is on friday, dec 28,) and i still have no clue about this stuff

Welcome to the forums! For the dimmer packs, whatever address you set it to (129 for your example) tells you all the address for each light. light one will be 129 and light 2 will be 130, 4 - 131, 5 - 132. so just use the faders (channels 129 - 132) to turn on the par cans. Make Sense?

For the ADJ Accu Spot 250 II's, I'm not entirely sure how to do what your thinking but what I would suggest is to set some scenes and just recall your scenes. Set the first light to the left of the runway and the second light to the right and save that as a scene. then just recall the scene during the show.

Hope this helps!!!

jthtiger

P.S. you may not get very many replies until everyone gets back in the office!

jpal welcome! and merry christmas. you could also try setting the light in the right on reverse pan and tilt. it should be either a feature on the op pro or you can do it on the lights in the system menu aswell. and the par cans was pretty well explained by jthtiger so i will leave it at that. if there is anything you dont understand or need further explaining let us know. peace! sincerely,

I assigned the dimmer pack to A129 as stated in the manual. then i set the dimmer pack to work for only 2 channels. then i plugged in a par can light to channel 1 and another par can light into channel 2. as you said, the console should make the channel 2 light work on the next fader which is 130.

but that's not whats happening.

Fader 129 is turning on both of the lights, and fader 130 doesn't do anything. I know the next thing u guys might say is check what outlet im plugging the par can lights into. i tripple checked each time, and i am plugging par1 into chan1 and par2 into chan2.

can you guys make any sense of this...


Also, I tried the reverse pan and tilt on one of the acu spots and that works great, plus i set a scene for what i needed it to focus on.

I still cant figure out how to localize where the acu spots focuses it lights, meaning if i am doing a stage program, how to get the lights to only play around on the ceiling, or only on the stage, or to go to the audience, and back and forth.

Thanks for the help.

hello
I need to know if the DMX Partner works wid 2 american dj moving heads 250 spot

@JPal

Congrats on getting you accu spots working. now for the dimmer pack. This particular pack has 3 modes (as you already know) 1 channel, 2 channel, and 4 channel. Here is how they work:

1 Channel
This setting allows all the lights plugged into the pack to be turned on/off using one channel. Meaning that if you set your pack to 1 channel mode and the address is at A129, when you turn on that fader all the lights will come on.

2 Channel
This setting allows the four channels to be turned on using only 2 DMX channels. So basically, if you have this setting on, you have a 2 channel dimmer pack with 4 edison sockets on each channel. Keeping with you situation if you turn on channel 129 then channels 1 and 2 on your pack will turn on. if you turn on DMX channel 130 then channels 3 and 4 will turn on. So if you want to use this setting plug your other light into the channel 3 spot.

4 Channel
This setting acts like a regular dimmer pack. I would recommend you use this setting no matter how many lights are plugged in. If you turn on DMX Channel 129 then channel 1 will turn on. 130 will turn on channel 2, 131 - channel 3, and 132 - 4.

I hope this helps you!

@estrello

yes your DMX partner will work with 2 american dj 250 spots but it will be limited to what you can do with it. good luck!

I hope this helps you!

wheew, long post!

jthtiger

Thank's
Then what is the controller that you suggest for 2 moving-heads 250 spot american dj?

estrello welcome! i would recommend a minimum of a DMX operator or even a magic 260 console. what type of programming did u plan on doing with these lights? where are you gonna use them mainly? peace! sincerely,

I'm going to try the 4channel mode when i get to the studio...

Also Jingles or jthtiger, do u knw how to localize where the acu spots focuses it lights, meaning if i am doing a stage program, how to get the lights to only play around on the ceiling, or only on the stage, or to go to the audience, and back and forth. or is this not possible.


And back to Par cans, how can i get to chase mode with the console. I was looking for this but i couldnt find it. I wanted to be able to record a chase sequences, but i cant get to the individualized switches that control the individual lights either.


Sorry for the long posts guys, its just my boss threw me into doing lighting for a semi big show, and i just received all the equipment, and the show is this friday, and ive been spending the past few days and night trying to figure out how to use the equipment. So far with your help, i'm getting somewhere...

I appreciate all the help you guys are giving me.

jpal you gonna want to program all those looks into the op pro. but what u can do is program those scenes and then add a fade time and hold time and create i think it is either caled chase or show on you pro and then have those run like that. anything else just ask. sincerely,

So, Im going to need to create a bunch of different scenes and then only can i create a chase or a show ?

well looking at the manual its says u can select you scenes that u recorded and enter them in a "show" u can also add scenes on the fly but since you are new to this i wouldn't try it just yet. so yes make your scenes and then add them to a show. understand? all this is in the manual just go slow and follow it step by step. good luck! sincerely,

quote:

Originally posted by jingles:
estrello welcome! i would recommend a minimum of a DMX operator or even a magic 260 console. what type of programming did u plan on doing with these lights? where are you gonna use them mainly? peace! sincerely,

Good day
I will use the machines in karaokes and parties

I wanted something less expensive than the magic 260
I want something practical, because I have other things to control

This message has been edited. Last edited by: estrello,

between the DMX Programmer and the DMX operator II, which is what you think is best