Skip to main content

Tagged With "Mute Mode"

Reply

Re: scene setter 24 dmx channel addressing

Carl N ·
I've watched both videos twice. I can find nowhere where it shows how to address the DMX channels. I did see that in program mode you need to hit program Flash 8 (not 6) three times. This allows access to the DMX channel programming but the manuals stes do not work. I may have a bad "new" unit and am currently awaiting a replacement.
Reply

Re: scene setter 24 dmx channel addressing

Luis ·
Hey Carl, To assign the DMX Channels on "ADJ" branded version of the Scene Setter you will need to do the following: 1. Enter Program Mode by pressing and holding the Record button and entering 1, 6, 6, 8. 2. Enter Channel Assign Mode by pressing and holding the Record button and entering 8, 8, 8. 3. Once this has been done the display will read 001, you can now use the Up or Down button to select the channel (1-512) that you want assigned. 4. Once your desired channel is displayed, tap the...
Reply

Re: spot and wash 250

elationpro ·
Hi Gustavo, The power spots all have a channel that does movement. So if you have 1 fader with a lever of 10%, that fixture may move on its own. On the DMX operator, you need to be in program mode, then reset all the faders. I am only guessing that's what it is. If not try addressing them all to A001, to see if it stops.
Reply

Re: gel color in 3d visulizer

homeboy ·
For Compu Pro 06 You need to: 1. Open program and 3D visualizer 2. Enter build mode on the 3D visualizer 3. Select the fixture(s) u want to change the color of 4. Select the color on the pallet To help find the buttons...
Reply

Re: Need help w/ DMX Operator

djsb101 ·
I know nothing about circuitboards & parts but damaged DMX driver chips sounds really bad. If it was the chips, how bad is it? Would I be better off sending it in to have it serviced or should I just buy a new controller? I didn't even think of checking the lights themselves to make sure nothing had happened to them. I'll set the lights to auto/sound mode & see if they're ok. Looks like I'll have to look into better surge protection and borrow a friends controller to make sure the...
Reply

Re: Compuware04 and SCX500's

Jingles8302 ·
do ur lights have 8 bit or 16 bit pan/tilt resolution. maybe u havw that feature turned off on the 1st 4 fixtures?? we are talking about the martin scx500's right?? if so check what dmx mode u have all the lights in. this is ali can think of right now. don't think it is the software. peace! jingles out!!!
Reply

Re: Help with DP-DMX-20L and DP 415 dimmer packs

homeboy ·
Of course they are! Its all DMX it doesn't matter if there is two different dimmer packs or any of the dmx consoles out there will all be able to control anything dmx WHEN USED PROPERLY. I don't mean to be harsh, but how much do you know about your console? The fat frog is a pretty high end console, you need a lot to happen for just one slider to control one light, its very complicated. Have you checked the patch? are you in one scene mode or two? what about the universe settings, master,...
Reply

Re: Basics of Compu Live 06

elationpro ·
Hi D-Rey, You have a good start, but your way off. What you want to do is start all over. In begginer mode, you can't delete or start over, so you will need to switch to expert mode. In expert mode, you need to create a new show. You will be prompted to save information. Don't save anything. Also you don't want to have any demo stuff. So creating a new show will remova all demo fixtures. Now.. Create a new page with your coemar fixture, and when you get to this section, you need to say you...
Reply

Re: "SNapping" Objects in 3D Visualizer?

Jingles8302 ·
once ur in construc mode u can right click a seires of truss or lights and move them all together or make em all in the same spot then spread them out one by one. don't know if this helps. jingles!
Reply

Re: Compu Live Questions

Jingles8302 ·
hey and welcome to the board. well i can tell this is gonna be a long post for me lol! now i acn answer most of these with ways that have worked for me but we should also see what elation says about the best way ot do some of these things. 1) you can assign a fader to adjust the speed of each individual button u have created by right clicking on the fixture page or if u have it in a master scene the master page scrool down till u see live toolbar button. u will see a size and dimmer andspeed...
Reply

Re: Compu Live Questions

matchless1 ·
Jingles, Thanks for your help. I tried what you said, and here's what I found: 1. I do have my Cycle created under the Master page, so I tried using the Live Toolbar Button. I do see the size, dimmer and speed controls, but only when I have a scene (like Blue) selected. When I click my "Cycle 1" button, the size, dimmer and speed controls disappear and are replaced with the text: "Cycle: Cycle 1". It's like all of those features are being disabled b/c I'm running a cycle instead of a scene...
Reply

Re: Compu Live Questions

matchless1 ·
Hi John, Thank you for your responses as well. 1. I tried what you said and made my chase a Scene using Easy Step. After that I was able to control the speed via the Live Button Toolbar. So, in other words, I did not need to do anything further using Easy Time. I tried it any way (yellow button making the channels Easy Time), but it just seemed to mess up my chase, so I went back to making all channels Easy Step. I notice that the F7 and F8 keys allow me to adjust the speed up and down. Is...
Reply

Re: Design Spot 250 Fade Issues

joeytech87 ·
No im programming scenes for the master page. it just sucks because i don't want to have to go in and change the dimmer channel on every light in edit mode.. is there a faster way.. we do a lot of programming and we need to do it quick. im seriously considering buying a brand new console.. ive had way too many issues with this elation software.
Reply

Re: Compu Live Questions

matchless1 ·
John, Thank you and Jingles for your help. It all really helped! I actually went ahead and ordered the program about a week ago. Today was the first chance I've had to make sure what I had programmed matched what actually happened. I have figured out most of the bugs, but there is still one I can't quite get: My 4 moving heads (Design Spot 250) initialize to a different position than what is shown on the visualizer. For example, in reality when I look at the MH's they sit on the ground in...
Reply

Re: Compu: RGBMix colorwheels disappearing!!

elationpro ·
Hi Level, I'm not sure what you mean by RGB color wheels? As color wheel and RGB color mixing are two different color options. For the Color wheel you have a group of color buttons. For RGB color mixing you have a color pick pallet for color picking. where you can click on the exact color you want. If this is what your refering to then you must be pressing the button rearangement icons at the top of the page. You must be in compression mode for the color pick pallet to show. Here is a small ...
Reply

Re: Audio

luisramirez ·
When you click the zoom function, do you click the fader and slide it or do you click the pallet then slide the fader? the proper way to do it is click the pallet then slide the fader. If none works maybe you need to go to the fixture and put it on a test mode and make sure that the zoom works that may be the problem, if it does work, then it is in the program, and you may need to edit if it is the program or re install it. As for the special (auto-music) it could be in the editing you may...
Reply

Re: Audio

elationpro ·
Kkiger, So the DLED 36 have a mic for stand alone mode. When you don't use a DMX controller it has microphone mode. But when you plug it in to a controller.. microphone mode goes away. The CMY zoom had music trigger as well. But when you select this option you need to crank up the music. These functions are found in the light not the software.
Reply

Re: RSER message

Jingles8302 ·
rst is reset. sounds like ur fixture is stuck in reset mode. it says this the whole time? do u have any control over DMX at all? u should give a call to the service department today if u have time. the number is on the main page here on the forum. peace! jingles.
Reply

Re: Out of sync Power Spot 250

Jingles8302 ·
it could be. but lets try it and see if it does anything ok? now maxamize ur 3D viewer and enter construction mode ok? then once u see the tabs. go to ur fixture tab and then open ur power spot folder and turn all the pan/tilt speeds off and see if it does anything ok? here is a pic to help ya out.
Reply

Re: Design 36 LED

pulighitng ·
I have took another look at a unit and in stand alone mode program 1- 7 have this neurotic strobing thing going on. This renders them almost useless in stand alone mode except program 8 unless your gig requires a neurotic theme I will ad a controller and look at the programs that way also
Reply

Re: Design 36 LED

pulighitng ·
switch 7 and 11 on for stand alone mode. 1+7 on = program 1 2+7 on = program 2... All of the programs except #8 (seitch 1+3+7+11) have a strobe part that makes the program look bad. If this is intended then it seems like a mistake.
Reply

Re: Design 36 LED

Jingles8302 ·
PU about ur previos question i believe all DLED36's have 7 channel capabilities. u just have to address them in 7 channel mode. now are you running all 20 of these with no DMX controler or are you using a dmx controler if so which one. try adressing them in 7 channel each and see if u have the master dimmer function on ch. 7. peace! jingles.
Reply

Re: Design 36 LED

pulighitng ·
My units are 6 channels like the manual says. 1= red 2= green 3= blue 4= FX 5= strobe 6= dimmer .I have had them on an Avolites Pearl, a strand 550, a Elation Magic 260 , a dove systems IQ512 and a Baxter systems pocket console. I love the light and am using them on a bunch of shows but as far as the internal programs go they are not performing in a manor that is suitable of a professional quality unit. Is it possible to upgrade the chip to function in seven channel mode? I also have 6 of...
Reply

Re: Design 36 LED

serraava ·
I have the same problems as well with a few Design LED 36s I just ordered. Great lights, but the standalone programs have strobing in them as well as the internal programs via DMX. Also, according to one of the paper manuals I have in front of me right now, there are two DMX modes. The first is 6 channel mode: R, G, B, Programs, Strobe, Dimmer. The second mode is 3 channel mode: R, G, B.
Reply

Re: Design 36 LED

Jingles8302 ·
guys im tellin ya. you can put them in 7-channel mode. i know i did it on compuware on the WFX booth this past month in atlanta. u have to allow 7 channels per unit to the next. try it and get back to me. channel 7 is a master dimmer. ok? peace! jingles.
Reply

Re: Design 36 LED

pulighitng ·
I have a great idea Jingles why dont you tell us how to put them in seven channel mode. My options are 3 and six and it does not matter how you address the control if the light can not be put in seven channel mode itself. I am standing by to buy 20 more units but it is now a long stand by.
Reply

Re: Nedd Help with scene transitions Newbie needs help

Jingles8302 ·
you could just program a blackout scene in the sequence befroe you want it to be on. just put it on a short hold time or fade time. also im not too sure about the power spots but in some lights there is whats called a "vector mode" which if u have that value selected it will black out when a either pan or tilt motor is moving or even color/gobo wheels moving. it is a cool effect, but again i didn't see it in the values of the power spot 250. peace! welcome to the forums. jingles.
Reply

Re: Octopod 80 with Magic 260 profile?

Jingles8302 ·
hello lemon! welcome to the forums. i think the problem your running into is the magic 260 controls only 16 channels per fixture. so if u want to run all the octopods as individuals you would have to buy more pixel drives in order to achieve this. because to control one set of octopods individually u would need a console that allows up to 48 DMX channels per fixture. u see the pixel drive and all 8 pods are considered (as far as your controller is concerned) as 1 fixture in the DMX line.
Reply

Re: Octopod 80 with Magic 260 profile?

lemonjello ·
thanks for your reply, so far I can control all 8 pods on one "fixture" second group on 2nd "fixture". is there any way to assign one pod to one fixture? the magic has 24 fixture buttons so theoretically could it be programmed channel 1-6 as fixture 1; 7-12 as fixture 2, etc? it seems pretty logical. According to dmx language or does the pixel drive override this? in 48 channel mode it allows for this, 6 ch per pod. Anyone else with experience or info?
Reply

Re: Octopod 80 with Magic 260 profile?

elationpro ·
Hi Lemon, Yes.. right now, you can control each pod individually. if you use the 48 ch. mode. So each pod will be 6 channels each. So pack 1 will start at 001 pack 2 will start at 049 pack 3 will start at 097 Ch 1 is rainbow ch 2 red ch 3 green ch 4 blue ch 5 strobe ch 6 chase If you use ch 6 to engage a chase of which you have 8 chases. ch 1 becomes speed time, and ch2 becomes fade time.
Reply

Re: Octopod 80 with Magic 260 profile?

elationpro ·
Hi Jingles.. That's actually incorrect. He can assign 1 pod per fixture button. in the 48 channel mode, basically every octopod becomes its own fixture with 8 channels to operate. so if he uses the alkalite profile on his magic he basically needs to set each fixture to be an alkalite fixture. so if he has 24 fixtures then he has control of each pod. Each pixel drive can be one fixture, two fixtures, 4 fixtures or 8 fixtures. Best regards,
Reply

Re: Lighting Newbie

tylerherron ·
@JPal Congrats on getting you accu spots working. now for the dimmer pack. This particular pack has 3 modes (as you already know) 1 channel, 2 channel, and 4 channel. Here is how they work: 1 Channel This setting allows all the lights plugged into the pack to be turned on/off using one channel. Meaning that if you set your pack to 1 channel mode and the address is at A129, when you turn on that fader all the lights will come on. 2 Channel This setting allows the four channels to be turned on...
Reply

Re: Lighting Newbie

jpal ·
I'm going to try the 4channel mode when i get to the studio... Also Jingles or jthtiger, do u knw how to localize where the acu spots focuses it lights, meaning if i am doing a stage program, how to get the lights to only play around on the ceiling, or only on the stage, or to go to the audience, and back and forth. or is this not possible. And back to Par cans, how can i get to chase mode with the console. I was looking for this but i couldnt find it. I wanted to be able to record a chase...
Reply

Re: Show Designer 3 manual question

elationpro ·
You want to record presets.. Page 18 of the manual. I am not finding missing letters in the manual.. can you let me know what pages? <b>CREATING AND RECORDING PRESETS</b> Before recording a preset you must first do some preparation. In order to be able to view certain moving light channels like color or gobo you will first need to raise the dimmer levels and set the pan and tilt positions in order to see the color or gobo selections. Do this by selecting the fixture or fixtures...
Reply

Re: Need .SSL file American DJ Revo III

stevelynch ·
Hey guys, any luck with the revoIII .ssl file? I've made 2 files, and cannot get them to work in any mode other than sound active... I'd like to be able to install this light tonight... I'll use sound mode if I have to, But I thought it would be cool to be able to have DMX control. I noticed no one has responded to this ssl request... does that mean It ain't happenin? I appreciate any help I can get... -Steve
Reply

Re: Need .SSL file American DJ Revo III

elationpro ·
This is an easy one guys. create a profile in the 4 ch mode. ch. 1 = mode.. do you want to be in pattern mode or chase mode. You can select this using ch1. Ch. 2 = the pattern or chase your secting. Ch. 3 = speed of either the pattern or chase. you need to select this after you select a pattern or chase. ch. 4 = dimmer.. if you don't have the dimmer on full then you wont see any pattern or chase. The 10 Ch mode is confusing.. I put a call into the ADJ pros and waiting to here back. Best regards,
Reply

Re: Need .SSL file American DJ Revo III

stevelynch ·
If I go into edit, it does in fact move things around, but once again, it doesn't really control the light... I only get three different patterns, and they don't chase or anything.. I mean there's some cool patterns in sound mode, but there's also some lame ones... it would be nice to have an actual fixture file for this light instead of half assing it through console.. the sliders on the fixture file do change the values in the output window, which would in a perfect world make the light...
Reply

Re: Magic 260 Issues

elationpro ·
Serra, My guy tested out the profiles with our fixtures, and everything worked just as good as if they were using 16 channels. What we found is that the profiles also work fine, and he informed me that he believes its a bad joy stick. The joystick could be sending bad commands that cause the lights to react. When your on 16 channel mode the joy stick is not active.. so it works perfect. When you use the profile, Joy stick is engaged and you have issues. If you just bought it you should be...
Reply

Re: OPTI 30 RGB

serraava ·
Thanks John. They are great little lights. The internal programs in them are fantistic. They are also very easy to set the mode and go to internal programs. They are a great price too, offering a lot of bang for the buck. I don't think I personally would ever use an Opti RGB because of the size of them. I would just rather spend the extra money and get DLED 36s instead. They are much smaller and more powerful. The problem I have with DLED 36s however, is they are dip switches unlike the Opti...
Reply

Re: black lights

pacman ·
We have controlled fluorescents with our lighting system by simply changing the dimmer to non-dim mode (it comes on full when the channel is at 50% or more - like a light switch). Would this work in your situation?
Reply

Re: Need .SSL file American DJ Revo III

Jingles8302 ·
ok but all i have is the 4 channel mode. i haven't tackled 10 ch. yet cause the traits for it are TOO confusing to me. waiting on elaboration from ADJ! chck your mail soon!
Reply

Re: black lights

serraava ·
Continuing on now: The buzzing noise is known as lamp sing, it's caused by the power being turned on and off really fast. The way this is fixed is more expensive dimmers have what is known as a choke after the SCR so the power change is as dramatic as on/off. The better the quality of dimmer, the less lamp sing you will get. Now why non-dim isn't really non-dim. Despite you setting a dimmer to non dim, either via the pack or the console, the power still passes through the SCR and choke. So,...
Reply

Re: COEmars and elation fixtures on the same control???

Jingles8302 ·
hey. have you tried getting rid of the pan and tilt preset speed in the 3D visualiser. here is a picture. if u notice the time and the arrow boxes that i highlighted you can use the arrow buttons to adjust the speed. i always turn these off. to get into to this mode on the 3D click on the hardhat. it is called construction mode. let me know if you need any help. sincerely,
Reply

Re: Request for basic newbie info...

manford ·
Alright, the verdict is in. I setup a simple chase, and activated it with both the audio and auto modes. Auto worked great, as I was able to set the speed to about 4 seconds, and the fade to around 3.8. All scanners moved nice and slow to the next chase step, just like I want. HOWEVER... Activate the audio chase, and everything just sort of stayed in the middle, trying to catch up. Seems like the FADE still applies to the chases in audio mode as well. Any way around this? Is there any method...
Reply

Re: Request for basic newbie info...

manford ·
Update! I have come up with a hardwired (literally) solution to the issue with fade time deactivation. I'll try to explain as clearly as I can, and apologize ahead of time if I lose anyone along the way. I'm using the Behringer FCB1010 to control the Operator 192 via MIDI. What I forgot about the 1010, is the ability to use the 2 built in "Switches" to control analog functions of amplifiers, just like a traditional stomp box that controls reverb/clean channel functions, etc. These are simple...
Reply

Re: Is there a 250 spot that will mix color like this?

elationpro ·
bdunard, Yes, a wash will be about from 40 brighter than a spot. You have a lot more light being projected along a bigger beam of light. However, that's all a wash fixture does.. color change.. but the beam of light it projects is impressive. Most rigs require a 1 to 1 ratio where you have 1 wash to every spot. So if you have 8 Spots you should also have 8 washes. But with the Frost filter of the Design Spot's it helps resolve not having to buy so many washes. Still the wash effect of a...
Reply

Re: Where do I get fixture profiles for Elation DLED TriBrick 36 and Tri64B?

bdunard ·
I am going to run the tri brick in 15 channel mode. I am going to use TriPar in 6 channel mode just like my DLED 36's. Yeah, today was supposed to be the day with the new toys...oh well I am plunking away on a Gateway for the time being.
Reply

Re: Design 36 LED

pulighitng ·
I was wondering if I am going to be getting replacement chips. I thought I would but as of now have not received any? I sent all my info. Can i buy the chips i would love to be able to rent my LEDs to some more weddings that want them in stand alone mode.
Reply

Re: Compu Live Question

Jingles8302 ·
Well easy show should not load automatically. the easy view which is the 3D visualizer may load automatically but try switching the rendering mode to normal see if that does it. Sincerely,
Reply

Re: Compu Live Question

elationpro ·
fishing.. when its a new install and you have all the demo pages still on it. The 3D window will always open up automatically because its in Demo mode. you need to delete all the Demo pages. this will stop 3d window from opening automatically. Partime, Jingles is your man to get started on the basic programming. send him an e-mail. Pro Bar flickering.. I would call our customer support department. 323-213-4593. sounds like a tech issue with the bar, not with the software. How much wattage...
 
×
×
×
×