Tagged With "Proteus Maximus Firmware V1.4.1"

Reply

Re: scene setter 24 dmx channel addressing

Carl N ·
Luis, I have tried that numerous times. Granted , it has been about 10 years since I have used DMX lighting. My last controller, An Election was a breeze to address. This is my second Scene Setter 24 in four weeks. The first one my salesperson and I assumed was defective. Now, for many years I have used XLR mic cables and I am learning that they may not work with todays new lighting components. I am assuming there is quit a difference between XLR and DMX cabling... So, I presently have...
Reply

Re: scene setter 24 dmx channel addressing

Jingles8302 ·
Hi, try these videos to see if they help: https://youtu.be/wu34OR7BtOA Part 1 https://youtu.be/Zsrpw-PEJxY Part 2
Reply

Re: scene setter 24 dmx channel addressing

Luis ·
Hey Carl, To assign the DMX Channels on "ADJ" branded version of the Scene Setter you will need to do the following: 1. Enter Program Mode by pressing and holding the Record button and entering 1, 6, 6, 8. 2. Enter Channel Assign Mode by pressing and holding the Record button and entering 8, 8, 8. 3. Once this has been done the display will read 001, you can now use the Up or Down button to select the channel (1-512) that you want assigned. 4. Once your desired channel is displayed, tap the...
Reply

Re: SD3 Playbacks containing presets, selected fixtures question

George Webb ·
Thanks SDMAN. I just tried using Scenes instead of Presets, but Scenes seem to have a few different problems: Scenes sometimes want to cancel each other when turning them on. (Does anyone know why this is?) This makes it hard to turn on multiple scenes simultaneously. When a scene fades out, it fades its channels down to zero, rather than letting them stay at their "color scene". I thought "HTP" would allow the highest value to control the channel, but apparently it means a controller will...
Reply

Re: SD3 Playbacks containing presets, selected fixtures question

George Webb ·
Here's a possible explanation: I noticed my fixtures' DMX channels are assigned to multiple fixtures, at least one of which is a single "32 channel DMX" fixture, which therefore contains all my 4 fixtures (7 channels each, channels 1~28). I don't know why they did that, versus setting up correct separate 7-channel profiles, but perhaps that would explain why the Scene recalls seem to be interfering with each other!? Maybe I should erase the whole console and start over? Still trying to get...
Reply

Re: Show Designer 1 Bricked

Rafael C. ·
To whom it may concern, The display PCB's have changed in time but it's the same operating system. It could be either a bad display or a bad PCB inside. If it's within the 2 year warranty your best bet would be to send it in for warranty repair. You can always send an email to rma@elationlighting.com to set you up with a RMA to send it in. If it's not under warranty anymore and if you have another working unit with the same color display, you can always start by trying to swap out the...
Reply

Re: DMX

madmikey ·
pan/tilt is inverted either on the fixture or in the software for address 1
Reply

Re: Compu Pro 06?

Jingles8302 ·
ok first of all when u got to ur "pages" page and u see the 3 little boxes? make sure all ur lights have a mark in the box that looks like a king crown. that will link all ur lights to work in the "master" page. now that all ur lights are lined up to work in the master page u can click on the master page abnd hit the new scene button and then click empty. and then when you edit it you will find that all ur fixtures are lined up ready to progrma all together for one nice synched effect. yes...
Reply

Re: Compu Pro 06?

ebaclights ·
I am not using any lights yet, just the viewer. I am only working with conventional fixtures on the program right now, so there is no home position. The lights fade out fine when I make a "fade out" button, but changing between scenes is what I cant get to work. Basically Say if I fade up fixtures 1-5 on my first scene, but on my second I want fixtures 6-10 to fade in, but 1-5 to fade out.
Reply

Re: spot and wash 250

elationpro ·
Hi Gustavo, The power spots all have a channel that does movement. So if you have 1 fader with a lever of 10%, that fixture may move on its own. On the DMX operator, you need to be in program mode, then reset all the faders. I am only guessing that's what it is. If not try addressing them all to A001, to see if it stops.
Reply

Re: Compu Pro Button Editor

elationpro ·
Hi Schadow, It sounds like you have the software conflicting itself. You shouldn't have more than one button trying to do the same thing. Also you should only have 1 edit window open at a time, unless of course its for a diffent fixture. If you havn't done to much programming try re creating a page. Best regards,
Reply

Re: Compu Pro Button Editor

schadow ·
Right now I have everything off. When everything is off (DMX output shows all channels off) I go to the Martin MX-1 page and click on "Center" and nothing happens. If you open the edit window for the Center switch all the settings look correct but its set to Blind-->Live and it wont change. Nothing else is open at this time so I don't have more than one button trying to do the same thing. This isn't a switch I created, this is the prerogrammed switch for the MX-1 from the Scanlibrary.
Reply

Re: gel color in 3d visulizer

homeboy ·
For Compu Pro 06 You need to: 1. Open program and 3D visualizer 2. Enter build mode on the 3D visualizer 3. Select the fixture(s) u want to change the color of 4. Select the color on the pallet To help find the buttons...
Reply

Re: Need help w/ DMX Operator

elationpro ·
Hi DJ, Yes it could be bad. If the DMX driver chips are damaged, then they will still work sound active. Try using your friends board and a light also to see if both your lights and controllers work. If it is DMX drivers, then you will have to send it in for service. No other way around it. Elation makes this device. DMX Branch 4. It is created to supress over voltage to the DMX signal. Once overvoltage goes through the line it takes everything out. However most people don't sell this or...
Reply

Re: Help w/ DMX addys

homeboy ·
The first pack should have only the first dip switch up and the second should have only the first and third up. This will make the channel 1 for the first and 5 for the second, thus covering all 8 channels you want. No, you can't separate the two plugs so you get 8 channels out of each pack, its strictly 4 channels. However, yes you can add more packs and "piggy back" or "daisy chain" (which ever term you prefer) off of the DMX outs from the last dimmer pack. You should already be doing this...
Reply

Re: need to know???

Jingles8302 ·
hey guys im doin it now but i find cause i have three reds in this fixture i think i does not sem to want to let me use 3 of em just two! also am i to click on the channels and enter in the numbers and signs for the channels patched to several diffeent outputs?? so for example that says 1= 0+1/40/60 and i enter in that in the box?? am i doin this right??? help me!! peace! jingles out!
Reply

Re: powerspot 250 lenses

homeboy ·
Page 40 "The lens should be changed at the first sign of ware, usually in about 1 – 2 years (lens will begin to look cloudy)."
Reply

Re: dmx profiles

elationpro ·
Hi Gary, You wouldn't need a profile for a dimmer packs. Dimmer packs are generic and don't have any special values, say colors or gobos or prisms. All you need to do is go to the generic page and use a par 56 or par 64. So if you have a 4 ch dimmer as you do with the dp-dmx20l you will use a par 56 then say you have 4 units. If you have a 12ch dimmer say like the Elation RMD-1210 you will use a par 56 and then put that you have 12 fixtures.
Reply

Re: powerspot 250 lenses

flash ·
Hey John Hear is a band that ia am working with this sat night. They do all Originals and 1 or 2 covers. There drummer is from California. (OUR AFTER )http://www.myspace.com/ourafter
Reply

Re: Compuware04 and SCX500's

Jingles8302 ·
do ur lights have 8 bit or 16 bit pan/tilt resolution. maybe u havw that feature turned off on the 1st 4 fixtures?? we are talking about the martin scx500's right?? if so check what dmx mode u have all the lights in. this is ali can think of right now. don't think it is the software. peace! jingles out!!!
Reply

Re: T-4 Controller Fuse

homeboy ·
I think this would be you best bet for parts from american dj... http://www.americandjparts.com/ProductDetails.aspx?Item...oductLine=PART&Qty=1 From another place... http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=140043778731 -Homeboy
Reply

Re: question about the vision scan 250!

djstelios70 ·
i recently purchased 4 mac entours, 2 visionscan 250`s and a magic 260 controller. i`m having trouble getting to show my scenes in action...i`m really not a software guy, more hardware. i also have a dmx 192 operator w/ joy. just looking for great advice since i upgraded my lightshow from 6 Trackspots w/ universal controller (which i mastered) and wish it didn`t have lightwave protocol. let me know guys...thanx
Reply

Re: question about the vision scan 250!

elationpro ·
Hi DJ, Those six lights are a nice set up. Your show will be looking good. What you need to learn is a few things to get going. 1. make sure you assing the right light to your fixture buttons. I'm not sure if the entour is in the memory of the magic so you may need to download the profile from the website and load it into your board using your U-link cable. If you don't have the u-link cable then you should get it. Once the fixtures are assigned the next step is to learn how to create 1...
Reply

Re: Help with DP-DMX-20L and DP 415 dimmer packs

steveperry ·
Thank you. Found the issue. I was attempting to address the DP415s as one channel each rather than 4 like the DP-DMX-20Ls are capable of. Once I fixed that issue and found a cabling issue everyhing started working. I appreciate the reassurances! Just some additional background on me. I was unsure about this as this is the first time I have ever had to do an install rather than just walk in turn on a board, plug in DMX lines and begin programming. It has been two years since I last used the...
Reply

Re: Upgrading to DMX operator 192- need guidance!

Jingles8302 ·
ok i will make this quick but if u need more info please ask! 1: yes it will. internal memory and that is what dmx boards do mainly. save show data. 2: nope! 3: no u cannot if u want ot do that get compuware. just my sugestion i love compuware. 4: i dunno the exact term if ur lights dim get the dpdmx20L if u just want to switch them off and on get a switch pack. peace! jingles! lighting guru! LOL
Reply

Re: length of riva 80 cables?

mikelights ·
The riva come with four(4) 3m and four(4) 6m cables. Each cable can be extended using the ECS-56 6m extension, up to 50' max run. It is a five wire data cable, we do sell the proprietary end connectors if you would like to make your own.
Reply

Re: length of riva 80 cables?

mikelights ·
Elation Service Dept. 866-245-6726 9 AM - 4 PM Pacific
Reply

Re: Basics of Compu Live 06

elationpro ·
Hi D-Rey, You have a good start, but your way off. What you want to do is start all over. In begginer mode, you can't delete or start over, so you will need to switch to expert mode. In expert mode, you need to create a new show. You will be prompted to save information. Don't save anything. Also you don't want to have any demo stuff. So creating a new show will remova all demo fixtures. Now.. Create a new page with your coemar fixture, and when you get to this section, you need to say you...
Reply

Re: Basics of Compu Live 06

d-rey ·
i did that, when i setup that switch it just moves to 4 different points in a cycle, the type of spot i was looking for is one that focuses on a certain point stays there until i move it. i was able to achieve this by setting a scene with with 2 fixtures pointed to the same spot and then moving them with the x/y preset button but i'm only able to control one fixture at a time. is there a way to have them both follow one mouse movement?
Reply

Re: eNODE 4 different firmwares

Zach.S ·
https://forums.elationlighting...ode-4-fixture-update The firmware is now Online. Please make sure that you use the correct file, depending on the version you already have.
Reply

Re: Why dosen't Elation have a parts section

rc ·
To whom it may concern, At this point in time Elation Service is limited on parts for the ACTIVE SCAN. That light has been discontinued for quite sometime and some parts are currently out of stock and on order. We do have the lamps in stock. The mirror and socket are also available. The main PCB's are currently out of stock and are on order. If you like to place and order for this lamp or any of these parts feel free to contact Elation Customer Support at 866.245.6726 (8AM - 4:30PM PST.)...
Reply

Re: Stupid Question but help

deleriousfishman ·
thanks mate. u are a great help. well its 4 30 am here so i am off to bed and when i get up you will be sleeping so i wanted to ask u a couple more things i can check the answers to later and if you could answer them then it is much appreciated. 1. i accidentily crossed off the real time screen that shows you the stage and your light show how do i get it back 2. how do i add music to the programme 3 how do i set the lights to follow the music jingles i cannot tell you how grateful i am to...
Reply

Re: Stupid Question but help

Jingles8302 ·
ok gn. del. 1) you se in the pic i posted at the top the lil circle with "3D" in it. click that that will re load ur 3d viewer. it looks like this: 2) your gonna want to use the program that comes with the emo called "easy show" it should be on your desktop. 3) to synch the lights to the music u have to first program some scenes and name them or just remember which ones they are. i use the master page alot for this. this is a really deailed part of programming on compuware. maybe i wil make...
Reply

Re: Magic 260

surgeprotech ·
Domi, 1. 1.02 is currently the latest version. 2. When using a preset, the fixture profile must match the fixture. What fixture are you controlling? 3. You'll need to initialize the channel names. When opening the Magic 260 uploader program, close the Ulink Ver 1.08 window. Go to show forms (located on the top left corner) and select EditChName. Select Init and save. The Channel names will now appear when creating a profile. Please call me if you continue to have any problems Sergio C.
Reply

Re: Compu Live Questions

Jingles8302 ·
hey and welcome to the board. well i can tell this is gonna be a long post for me lol! now i acn answer most of these with ways that have worked for me but we should also see what elation says about the best way ot do some of these things. 1) you can assign a fader to adjust the speed of each individual button u have created by right clicking on the fixture page or if u have it in a master scene the master page scrool down till u see live toolbar button. u will see a size and dimmer andspeed...
Reply

Re: Compu Live Questions

matchless1 ·
Jingles, Thanks for your help. I tried what you said, and here's what I found: 1. I do have my Cycle created under the Master page, so I tried using the Live Toolbar Button. I do see the size, dimmer and speed controls, but only when I have a scene (like Blue) selected. When I click my "Cycle 1" button, the size, dimmer and speed controls disappear and are replaced with the text: "Cycle: Cycle 1". It's like all of those features are being disabled b/c I'm running a cycle instead of a scene...
Reply

Re: Compu Live Questions

elationpro ·
Hi Matchless1 I wanted to jump in and help out a bit. For Q1. You cannot control the speed of a cycle with 1 slider. What you would need to do for this is create steps using EASY STEP in the edit window of a scene. After multiple steps have been created, you need to convert the Easy step to EASY TIME using a yellow button labled Easy Time. This is where the faders Jingles was talking about kick in. Q2. The 3D window works seperatly from the real life fixtures. The attributes created are...
Reply

Re: Compu Live Questions

matchless1 ·
Hi John, Thank you for your responses as well. 1. I tried what you said and made my chase a Scene using Easy Step. After that I was able to control the speed via the Live Button Toolbar. So, in other words, I did not need to do anything further using Easy Time. I tried it any way (yellow button making the channels Easy Time), but it just seemed to mess up my chase, so I went back to making all channels Easy Step. I notice that the F7 and F8 keys allow me to adjust the speed up and down. Is...
Reply

Re: Compu Live Questions

elationpro ·
Brian, I am really impressed on how you picked everything up. So to move forward, you can achieve the tempo your looking for by activating the Audio function in Compu Live. Step 1. In the "controller" drop down menu look for "Starting parameters". Then in the Options box, choose "Audio/Midi" and in this new window, click on the check box with the speaker icon. Then close all windows. You will be prompted to restart, and the Audio Analizer box will open automaticly. Minimize this for a...
Reply

Re: Design Spot 250 Fade Issues

elationpro ·
Hi Joey, That's wierd. I just programmed a few scenes and I am not getting the strobing effect with the design spots. I think its a matter of how your recording your scenes. For example If I have scene 1 lights on with blue wave gobo in position 1. I would then simply bring the dimmer down to zero and record scene 2 with the dimmer all the way down. So when I go from scene 1 to scene 2 and I add a fade time, the dimmer takes the time to dim, and thus no strobing. I just thought about it and...
Reply

Re: Design Spot 250 Fade Issues

elationpro ·
Ahhh! Ok.. Your starting from INIT. This makes sense as with INIT all values of the moving light are off. So when you fade on, every function is fading. In programming you need to get used to creating set up scenes. A set up scene is the scene you want to be active before your actual scene comes on. This is what I was talking about when I suggested to create the scene you want, and bring down all the dimmers. Record that as the scene. Position, color, gobo, but dimmer off. then simply turn...
Reply

Re: DMX Operator 192

djinsomnia ·
That def helped a huuuuuuuge amount. So basically there are 8 scenes on the 192. So I can only do 8 movements and changes total for 1 chase?
Reply

Re: DMX Operator 192

Jingles8302 ·
no on the op u have 30 banks of 8 scenes each. and 12 chases that can hold up to 240 scenes. so basically u cna have 1 chase full to the max of 240 scenes which is like putting every scene u can record on the operator into a chase. so let me break it down even further for ya. u cna store any scene as many times as u want and in any order u want in a chase as long as don't go over 240 scenes but u can also continue on ur chase into the next one. i have done that and it works fine. do u know...
Reply

Re: dmx stregnth

surgeprotech ·
The resistor you'll need is a 1/4 watt between 90-120 ohm.
Reply

Re: Compu Live Questions

matchless1 ·
John, Thank you and Jingles for your help. It all really helped! I actually went ahead and ordered the program about a week ago. Today was the first chance I've had to make sure what I had programmed matched what actually happened. I have figured out most of the bugs, but there is still one I can't quite get: My 4 moving heads (Design Spot 250) initialize to a different position than what is shown on the visualizer. For example, in reality when I look at the MH's they sit on the ground in...
Reply

Re: Compu Live Questions

elationpro ·
Hi Matchless, Yes, I know what your talking about.. and you have a few simple modifications to work with. 1. The Design Spot 250 has two pan degree settings. The degree is the amount of spin from left to right that the light can move. It should be set to 540 degrees on the light to match the 3D window. 2. Once this is done, then on the 3D window you may want to invert the pan and tilt to match the direction of the actual light. Here is a picture to help you find the pan and tilt inversion.
Reply

Re: Compu Live Questions

matchless1 ·
John, 1. I changed the degree angle from 630 to 540 on the light. I even reset the pan motors on the light. Unfortunately, this did not affect the "home" position of the light. It looks like I'm still off by 45-90 degrees on the pan. 2. Also, I did invert the pan last night to get the movement direction corrected (i.e. Clockwise vs. Counter Clockwise pan). So anyway, ?????, still can't get my "home" positions to match the viewer. And, yes, it does affect every movement in real life after...
Reply

Re: Compu 06 Help

ebaclights ·
Its a lightronics RD-121 12x1.2 Ive been at the church today messing with it, and if I do anything for then 4-5 seconds, its really jerky, like its dimming in small steps instead of a smooth fade.
Reply

Re: Stage setter 8 question

surgeprotech ·
I assume that you're using dimmer packs. Are you exceeding the maximum load? How many packs are you using? If more than 1, do you have them on separate circuits? Is the dmx line terminated
Reply

Re: Stage setter 8 question

waynek ·
Thanks for the response. We use 2 elationdmx20l dimmer paks on separate circuits, 4 par cans on each, and to the best of my knowledge the dmx line is terminated properly. I don't believe we are exceeding the maximum load as the lights worked fine all last year.
 
×
×
×
×