Skip to main content

Tagged With "Firmware V1.13"

Everything
Reply

Re: External MIDI Trigger for BMP Rate

elationpro ·
Matchless.. see if you can wrap your head around this. 1. create scenes or switches with 1 color each 2. create cycle with each of the colors 3. change the time for each scene/switch to GO inside the cycle 4. now when you click PAGE-DOWN on your keyboard, you control the timing of the cycle 5. to assign this PAGE-DOWN control to MIDI, open the CONSOLE window 6. right-click on the MIDI controller button that you want to use (any button will work) 7. you will see a blank area with 4 icons to...
Reply

Re: Stager 8 Pack - question

Jingles8302 ·
Welcome to the forums! The DP415 is only a 4 channel dimmer pack, how many do you have? You would need to address the first pack at a starting address of 9. The net pack at a starting address of 13 and that should be all you need for your pars. We have a dip switch calculator HERE if you need help with dip switch settings. Let me know if this helps. Sincerely,
Reply

Re: Show Designer 1: programing multiple lights as one fixture

dan4governor ·
Thanks SerraAva, I set up my lights on the same channel and I am able to control them as one fixture. However, I don't think I was specific enough with my question. I was wondering if I could set up the lights as one fixture, but still control them individually. For example, I have several American DJ par 64 LEDs that use 6 DMX channels. A fixture can support 32 DMX channels. Is there a way I can set them up so that faders 1-6 control par 1, 7-12 control par 2, 13-18 control par 3...and so...
Reply

Re: How does everyone organize their scenes/switches/etc

misebeam ·
Hi David, I am in a tribute band, and had the same question, what I came up with was pages will not work, unless all fixtures are on the pages...(which is hard and from what I can see can’t happen due to DMX addresses). So what I did is on the master page, I click edit, and click on "Compression”( either a scene or switch) and make short names for each of the songs like "1ofdays" for “one of these days”, and so on. After I made the compression, I then went back to the master page where all...
Reply

Re: Configuration SD3

elationpro ·
The SD3 needs 1 value for the Step DMX. When you use data wheels on console it needs to know a number value. It cannot understand 0-14 it needs one number. the number can be any number from 0-14. it can be 2 it can be 4 it can also be 13. However it is best for the performance of the fixture to select a value inbetween the 2 values that you have. say you have values 20 - 40 for color red.. then you want your step value to be 30 for best performance and least problems.
Reply

Re: Compu-live USB/DMX Dongle - Led's and Buttons

roberta ·
Email with dongle info has been sent. 1/20/10 13:37 CT. I await your reply, thanks.
Reply

Re: Need help with DP-DMX4B

serraava ·
Older dimmer pack, so no channel mode on it. Sorry about that. Seems to be something else wrong. First, what types of fixtures are you using and how are they lamped wattage wise? Second, with 4 channels per pack, the first should be addressed 1, second 5, third is 9, and last is 13. Third, which console are you using? Hopefully one of these questions points us in the right direction.
Reply

Re: Need help with DP-DMX4B

studio42 ·
Sorry, I didn't read the manual. Now I did. Whee!!!!! Dip switches. Oh joy! 1: 5 amps per channel, so don't go nuts on this unit. 2: The way I see it, there is no mode function, so it's a 4-channel dimmer, just like the manual says in it's one page. The channels should be set 1, 5, 9, 13..... Ideally no overlap. 3: What Serra Ava is asking: What are you using to control this? 4: Any other lights show up: Channels 1-4, which ones light up? 5: Where are you plugging in things?
Reply

Re: Powerspot 575 Fuse Issue

serraava ·
Hi Dano30 and welcome to the forums. Your problem, most likely, is do to the fact that they are plugged into dimmers. You are lucky you are only losing fuses. Dimmers, even parked at full, still dim because they are still run power through the choke. Unless you have non-dim, switch, or Sine Wave modules, plugging them into dimmers isn't good for the fixtures. For example, a theatre around here once rented 13 Mac 700s. Well, they plugged them into dimmers and then end up returning them early...
Reply

Re: Operator 192 with Chauvet 4 dimmer and conventional par 64's with dimmer pack

yupyup ·
Hi WideGlide I'm new to this stuff also, but here's what I've learned so far. The 16 pars; each light should be plugged into it's own outlet on the DP(dimmer Pack). Most DP's have DUAL outlets on each channel, if you want to have individual control of each par lamp, use "ONLY 1" of the DUAL outlets for each lamp. The Op192 (Operator 192) has 12 fixtures each able to control 16 channels (12x16=192). Fixture 1 can control ch1-16. Fixture 2 can control ch17-32. Fixture 3 can control ch33-48.
Reply

Re: Where do you get lighting ideas

studio42 ·
Well, all I can say is I like Korg gear. I have plenty. Korg nano KONTROL, KEY, PAD. DS-8(considered to be the better keyboard to the Yamaha DX-7, but didn't get the respect!) M3-R(stripped down original M1-R) with RE-1 editor Wavestation SR DDD-5 drum machine KMX-112 12-channel keyboard mixer and I think some other Korg stuff, including pedals. So, I can say I like Korg. My initial thoughts were, "gee, this sounds like a power issue". You're also lucky you didn't lose your SD card. Make a...
Reply

Re: Console selection help

hobson ·
I like your "fancy go switch" idea. Let me know what kind of midi controller you choose. The FCB1010 would do the trick. I also think your idea of loading a new set of scenes every break will work (although I wouldn't want to hassle with that at a gig). I've got a couple of fairly inexpensive ADJ Aggressor LEDs that I aim at the audience and plug it's power into a DP-415. I use the Auxiliary Buttons on the M260 to turn them on during leads. You could either do that if anyone in the band has...
Reply

Re: Help w/ Profiles

illuminati ·
I am not sure what I can send you, most of it was on my old computer. The elites never had manuals, they had a little info online but that company doesnt exist. But I know they're CH1 function, CH2 speed, 3=R,4=G, 5=B, the CH 1 is split up into functions as well. The generic cans might not have a manual either, theyre 1=r, 2=G, 3=B, 4=W, 5=function, 6=rate....I use the 6CH generic that came w/ the board, ONLY ch 1 (red dims) The rest of my fixtures (Mega Panels and TriPhases)are ADJ, so I...
Reply

Re: Need help getting started with midi control and magic 260

hobson ·
You actually have an ideal situation to take great advantage of the M260 - assuming your keyboard guy isn't using all 16 midi channels in his sequences. You can use the sequencer to trigger either Scenes or Shows to good advantage. A Scene is created by using the M260 to set all of your lights in a condition that you will want to use sometime during the gig - and recording it to a particular button on a particular page of the M260. As long as that Scene is turned on, nothing about the lights...
Reply

Re: adress for dp415

bbobm ·
thnx ! so if i i get aanother dimmer pack and want to use channels 13-16 i need to dip switch on 1 and 5
Reply

Re: adress for dp415

elationpro ·
dimmer pack 4 - dip switch 1, 3 and 4 ON. Pack 4 will be channel 13-16
Reply

Re: Duplicate a Fixture

bender1 ·
Jingles, I still have an issue with this even with the latest version of the software (Dec 13, 2010). Is there an email address I can hit you up on please? Thanks Matt
Reply

Re: Better DMX Addressing for Multi Fixtures

thex-man ·
No, the profile just says, Chauvet folder>Colorstripmini. I noticed that in the pages of the Compu Live program that it has the buttons to click on for "auto" and "color change" but it just does not seem to function right. On the Mini Spots, I will see if the way I have the Addresses set have something to do with it. Now, I will also give each fixture it's own address as well BUT, When I put all these together, should I give the addresses in the order that they are in the array? For...
Reply

Re: Starting a new page Problem

bryanb ·
Sorry it's been so long. I had to put the software down for a bit and use other things. But-- I am using the preinstalled library, and tried using the network connected, but the software wll not let me select (check the box) of the chauvet colorado 1. Version date is Dec 13 2010 I am using an HP Mini laptop with Windows 7 Starter. An compu 1024ec and I am planning on syncing a Behringer BCF2000 if I can get the compulive software to function.. Thanks- Bryan
Reply

Re: Show Designer 2 monitor software help

nmwallace ·
Ken, do you have a link or picture so I know what you're talking about? I'd call myself an "intermediate" computer user, so I know stuff like how to open DOS and how to replace a HDD, but I'm not entirely sure what you mean by "swapping pins 2 and 3." Also, I'm using a Macbook 13 running Windows 7, so is there a specific cable I need that would work better than the one I have? Like I said before, links and pictures would be super helpful for me.
Reply

Re: saving shows

karl ·
I save the ssh file after adjusting the windows and setting scenes. Just tried again with no luck. The release date is Dec 13 2010. I don't know how to identify the interface model.
Reply

Re: Compu crashed my computer

danielg ·
About said Compu Live 2006 Dec 13 2010 SL1024EC
Reply

Re: Scene Setter (24)

joegardner ·
Sure. the upper bank (1-12) would be one scene with the second bank (13-24) being the preset for the second. It would only have a total of 12 active channels
Reply

Re: DIP SWITCH SETTINGS 101

anthonywhite ·
Ok, so this is cheating, but when you are under the gun with a crew that [might] suck. This is easy... Enjoy.
Reply

Re: DIP SWITCH SETTINGS 101

tylerherron ·
ok set your first light to channel 1 (DIP Switch 1 up, the rest off) then your second light to channel 6 (DIP switches 2,3 on, rest off) your third light to channel 11 (1,2,4 on, rest off) and fourth to channel 16 and so on just adding 5 channels. A little semi-visual presentation showing you Light One(addressed to channel 1): Ch. 1 - not used yet Ch. 2 - strobe Ch. 3 - red Ch. 4 - green Ch. 5 - blue Light Two(addressed to channel 6): Ch. 6 - not used yet Ch. 7 - strobe Ch. 8 - red Ch. 9 -...
Reply

Re: Design Brick 70 II

elationpro ·
all good questions.. will investigate.
Reply

Re: Default fixture list and adding new fixtures...

jfetter ·
Hmmm, actually it does! I knew I saw it someplace but check out page 13 of the manual; "Section 11: Choose Fixtures The first thing you will need to do is choose the fixtures that you will control with your MAGIC 260. There is an internal fixture library that contains most Elation Professional and ADJ DMX fixtures." Jack ;-)
Reply

Re: I need help!

Jingles8302 ·
Use the bundle function. Read page 13 of this: http://www.elationlighting.com..._manual_en_10324.pdf Sincerely,
Reply

Re: Intimidator spot led 250 chauvet profile

Jingles8302 ·
Yup I do. 8 channel mode 13 channel mode Sincerely,
Reply

Re: G Lite SW 600

d-lights28a ·
Here are the channel assignments I got from the PDF I sent you. I need the 18 channel 16 bit mode. 1- Lamp On/ Reset 2- Dimmer 3- Shutter/Strobe 4- Pan Course 5- Tilt Course 6- Color Wheel A 7- Gobo Wheel B 8- Gobo Wheel A 9- Gobo Wheel Rotate 10- Iris 11- Focus 12- Zoom 13- Prism Rotate 14- Color Wheel B 15- Blackout movement/ Functions 16- Pan/Tilt Speed 17- Pan Fine 18- Tilt Fine Hope this helps. 18 channel 16 bit mode is what im lookin for.
Reply

Re: G Lite SW 600

Jingles8302 ·
I made this based off of the info quoted above. The PDF is really blurry to read. Hope this will suffice. http://db.tt/6E3JA1XV Sincerely,
Reply

Re: Scene Setter (24)

sterlingaug ·
I totally agree that the manual is confusing. If you want to use only 1 scene then the dimmers work without any programming. If you want 2 or more different lighting scenes then you MUST program them in and assign the scenes to one of the flash buttons (13-24).
Reply

Re: 16bit scanner programming issues

JWPardee (Guest) ·
Try a few things for me, see if we can narrow down the issue a little bit here. I attached a link bellow to the 918 user manual, the data and layouts are similar between the two types of lights. First, on page 12/13 of the manual it tells you how to reset the fixtures to default settings. This will clear up any preset issues that might cause errors in the data. Second, on page 14, it tells you how to set the mode of DMX...for the controller you are using, Mod2 is what you want. The Vector...
Reply

Re: Profiles for X-Laser Mobile Beat RGB & ADJ Vizi Beam 5R Needed for Compu Show!

djwhirl ·
I am Using Compu Show (Beta) and a Win 7 Boot-Camped MacBook Pro 13" 2012 Model i5 w/ 16GB Ram & 256SSD. I split the HDD in half....128GB for OS X & 128GB for Win 7. Thank you for the profiles Jeffery, but I am new to Compu Show, Can you help me figure out how to creat a scene to keep my lights that are positioned up-right on top of 8' Global Trusses to stay on my dance floor instead of giving me an ariel show? (Tired of being shot in the face by my own lights....lol.) James
Reply

Re: changing a ssl2 profile to xml

soundsyco ·
Thank You, so I can give you guys the owners manual or channel assignments and you guys can create a profile. I hope this is where I can give you the channel assignments. Thanks chnl 1 pan 0-255 0-540 degrees chnl 2 pan 16 bit 0-255 16 bit adjustment chnl 3 tilt 0-255 0-270 degrees chnl 4 tilt 16 bit 0-255 16 bit adjustment chnl 5 pan/tilt speed 0-255 from fast to slow chnl 6 strobe 0-255 strobe from slow to fast chnl 7 Dimmer 0-255 from dark to full light chnl 8 Color wheel 0-5 white 6-30...
Reply

Re: Intellegent Lighting & Dimmer Packs

cahedger ·
Hey Jingles, Hope you had a good weekend. Not tripping any breakers (that I know of), and I've tried running my monitor to a completely different outlet (the strobe was the only light on that dimmer at the moment)... the monitor shuts off while the strobe runs, and comes back on when the strobe shuts off. It's the American DJ Mega Flash DMX and looks like it's a 2 channel. So to refresh on the setup, would I be able to daisy chain my strobes and lasers together w/ the lasers addressed as...
Reply

Re: Level Q7 Profile

Jingles8302 ·
I fixed it for you, it'll look like a shurnken par can and it will be a wash light beam output and should be a good 13 degree beam angle in the 3D. https://www.dropbox.com/s/k83q...djt85g/Level_Q7.ssl2 Sorry about that! If you run into any more bad 3D profiles, let me know. Thanks!
Reply

Re: Satura Series Fixture Firmware

elationservice ·
Updated August 9th 2019 with new release.
Reply

Re: Satura Series Fixture Firmware

elationservice ·
Updated original post Nov. 11th, 2019 with V1.0.10
Reply

Re: SD1 and Generic Dimmer pack programming

SquireDude ·
Hi, After multiple tests using either of the Generic Dimmers definitions… I found that one definition is only 2 chnl and the other definition is 3 chnls. Instead of defining it as a Generic Dimmer pack I used RGBW and now I have all 4 channels working fine. Thanks, Phillip
Reply

Re: Ficture File ClayPaky Axcor Spot 300

test ·
Here are the DMX-Sheet
Reply

Re: Problem with eNode 8 Pro / sACN and ETC Gio Lighting Desk

Jingles8302 ·
Hi you need to update the Enode 8 PRO to firmware 2.8, attached is the user manual. you may need to email firmware@elationlighting.com to get the firmware.
Reply

Re: SixBar 500 Firmware

elationservice ·
UPDATED LINK TO NEWEST FIRMWARE.
Reply

Re: SixBar 500 Firmware

Youri Gidding ·
any release notes or list of changes available?
Topic

SixBar 500 Firmware

elationservice ·
Uploader Tool Needed: C-Loader SixBar 500 Firmware V1.15 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

ACL Bar 360 Fixture Firmware

elationservice ·
Upload tool: CUE Software Uploader ACL Bar 360 Fixture Firmware V1.28 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

DTW Bar 1000 Fixture Firmware

elationservice ·
Necessary upload tool: CUE Software Uploader DTW Bar 1000 Firmware V1.13 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

Fuze Par Z60IP Firmware V1.07

elationservice ·
Firmware Tool Required: C-Loader II Fuze Par Z60IP FW V1.07 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your...
Topic

ZCL Bar Z 300IP Firmware

elationservice ·
Upload tool: C-Loader ZCL Bar Z 300IP Firmware V1.03 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture...
Topic

Six Par Z19IP Fixture Firmware

elationservice ·
Upload tool: C-Loader or USB Stick Six Par Z19IP Firmware V 1.07 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see...
×
×
×
×