Skip to main content

Tagged With "Firmware V1.21"

Everything
Reply

Re: help!! easyshow/laptop crash

nickcarbone ·
21, and a struggling musician, so I'll have to keep up the hard work until I can call myself successful. if you think dmx lighting is hard, try getting 4 guys to pick one damn publicity photo out of 1000...o yea and agree on the same one.
Reply

Re: Design Spot 300 Manual

Jingles8302 ·
no it uses 21 DMX channels. the wash uses 16 i believe. sincerely,
Reply

Re: External MIDI Trigger for BMP Rate

elationpro ·
Matchless.. see if you can wrap your head around this. 1. create scenes or switches with 1 color each 2. create cycle with each of the colors 3. change the time for each scene/switch to GO inside the cycle 4. now when you click PAGE-DOWN on your keyboard, you control the timing of the cycle 5. to assign this PAGE-DOWN control to MIDI, open the CONSOLE window 6. right-click on the MIDI controller button that you want to use (any button will work) 7. you will see a blank area with 4 icons to...
Reply

Re: Does the 300E have optional lenses?

bdunard ·
Yes I realize the 300E is only 21 degrees. However, the 300 pro goes to 41 degrees with it's optics if I read correctly. I only need a really wide lens so I was hoping that there was wide angle lens option for the 300E.
Reply

Re: How does everyone organize their scenes/switches/etc

misebeam ·
Hi David, I am in a tribute band, and had the same question, what I came up with was pages will not work, unless all fixtures are on the pages...(which is hard and from what I can see can’t happen due to DMX addresses). So what I did is on the master page, I click edit, and click on "Compression”( either a scene or switch) and make short names for each of the songs like "1ofdays" for “one of these days”, and so on. After I made the compression, I then went back to the master page where all...
Reply

Re: Magic260 Software - Edit Fixture and Magic 260 Controller

Jingles8302 ·
In the creator the "Step"s are for each preset in a fixture. For example a color wheel will have several steps like 0-10 white/open. 11-20 red, 21-30 blue, etc. Make sense? Each step in the profile creator is a preset in the DMX chart. The reason the magic scrolls in increments of 5 DMX values is because it is easier to scroll through the whole 0-255 range this way without constantly rotating the wheel. If you want to scroll exactly through each specific value press the "Fine" button and...
Reply

Re: SD3 Profile

sdman ·
The profile that's in the download section is the standard 23 channel mode. There is a 21 channel mode but it only leaves off the fine modes for pan and tilt.
Reply

Re: Better DMX Addressing for Multi Fixtures

thex-man ·
No, the profile just says, Chauvet folder>Colorstripmini. I noticed that in the pages of the Compu Live program that it has the buttons to click on for "auto" and "color change" but it just does not seem to function right. On the Mini Spots, I will see if the way I have the Addresses set have something to do with it. Now, I will also give each fixture it's own address as well BUT, When I put all these together, should I give the addresses in the order that they are in the array? For...
Reply

Re: Sound Active programs

djequis ·
Hello James, I hope all is well. I recently updated to version 1.03.31 of emulation. I have lost the capability of controlling my Chauvet Q-Spot 260 LED moving heads. I think the issues I am experiencing is due to the sound active features that were created. As much as I like the sound active feature I need to have control of my light. Can you please advise on what I should do? i have a Wedding on 4/21 that I need to get my issues resolved by. I don't mind going back to the previous version.
Reply

Re: Fixture Profiles needed

aurora ·
http://www.laserworld.com/en/s...ml?func=select&id=21 Here is a link for the laserworld pdf manual. I have the stairville product manual in a pdf format, but no link, what do i do about this? Can I email the file to somebody?
Reply

Re: Magic260 Software - Edit Fixture and Magic 260 Controller

henri ·
Re: Magic260 Software - Edit Fixture and Magic 260 Controller
Reply

Re: Magic 260 Problems

hobson ·
The first M260 I had constantly lost its fixtures. Elation replaced it. The replacement is much more stable, but I never go to a gig without a lap top with which I can reload the fixtures - and I have to use occasionally. I don't use the blackout button, so I can't help you fix it. Instead, I use button 23 on each page of Shows as my blackout setting, buttons 21 and 22 as super flashy light shows, and button 24 as a low lever, between song light scene. In this way when we play a song that...
Reply

Re: DIP SWITCH SETTINGS 101

anthonywhite ·
Ok, so this is cheating, but when you are under the gun with a crew that [might] suck. This is easy... Enjoy.
Reply

Re: Problems with compu 2006 with 1024EC

verchern ·
Yes. If I am using the USB box with programmed scenes, it works fine. If I am using the easy stand alone program on the PC, I have issues. The LEDs are NOT plugged into the dimmer. The dimmer runs all of the house incandescent lights only. The LEDs are powered from straight 120v circuits (no dimmers) with DMX control. According to Tech support, the new software dated 12-21-07 on your web site should fix this issue. I downloaded it today and will let you know.
Reply

Re: Problems with uni pak 2 and compu live

jhdd ·
It's the standard one in the library C:\SL2006\ScanLibrary\Elation Pro\UNI PAK.SSL Is there a new profile for the UNI PAK II? I've tried both verions of the SSL April, Dec 21, 2007 updates of Compu Live. I see it in the output window and in the 3D viewer and it seems to work in both as I slide the dimmer on the page. Maybe the setting are wrong on the dimmer pack itself. The address is set to 168, swith is off, dimmer limit 100 and preset is zero. THANKS,
Reply

Re: compu live update now available!

ebaclights ·
I understand. I hope you guys will note on the new link, or make a post on here when you update it. If the new link just says Compu Live 2006 Software - December 21, 2007, we have no way to know its the fixed one. Also, thought I would bring it your attention, the top banner on your software has "professional" misspelled.
Reply

Re: Design Brick 70 II

elationpro ·
all good questions.. will investigate.
Reply

Re: moving head led wash 12 channel

tap ·
This is the chart for the light Channel #1 Pan Channel #2 Fine Pan (moves very slightly for finer accuracy) Channel #3 Tilt Channel #4 Fine Tilt (moves very slightly for finer accuracy) Channel #5 0-255 Pan and Tilt movement speed (fast-slow) Channel #6 0-7 Closed 8-134 Master dim (bright-dim) 135-239 Strobe (slow-fast) 240-255 Open Channel #7 0-255 Controls Red LED's (dim-bright) Channel #8 0-255 Controls Green LED's (dim-bright) Channel #9 0-255 Controls Blue LED's (dim-bright) Channel #10...
Reply

Re: Satura Series Fixture Firmware

elationservice ·
Updated August 9th 2019 with new release.
Reply

Re: Satura Series Fixture Firmware

elationservice ·
Updated original post Nov. 11th, 2019 with V1.0.10
Reply

Re: Ficture File ClayPaky Axcor Spot 300

test ·
Here are the DMX-Sheet
Topic

Newest update

bubbajoe ·
Hey. A couple of nights ago my show crashed and it was not pretty but I figured out that it was my new midicon that caused the crash. I am not currently running the newest version and I know that I should but where can I find the newest update for Compu live 2006. Also how do I update the software and finally will my old showfiles still work with this newer version? I am currently running the March 21, 2008, Sl1024 EC Version.
Reply

Re: Problem with eNode 8 Pro / sACN and ETC Gio Lighting Desk

Jingles8302 ·
Hi you need to update the Enode 8 PRO to firmware 2.8, attached is the user manual. you may need to email firmware@elationlighting.com to get the firmware.
Reply

Re: SixBar 500 Firmware

elationservice ·
UPDATED LINK TO NEWEST FIRMWARE.
Reply

Re: SixBar 500 Firmware

Youri Gidding ·
any release notes or list of changes available?
Topic

SixBar 500 Firmware

elationservice ·
Uploader Tool Needed: C-Loader SixBar 500 Firmware V1.15 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

ACL Bar 360 Fixture Firmware

elationservice ·
Upload tool: CUE Software Uploader ACL Bar 360 Fixture Firmware V1.28 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

DTW Bar 1000 Fixture Firmware

elationservice ·
Necessary upload tool: CUE Software Uploader DTW Bar 1000 Firmware V1.13 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

Fuze Par Z60IP Firmware V1.07

elationservice ·
Firmware Tool Required: C-Loader II Fuze Par Z60IP FW V1.07 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your...
Topic

ZCL Bar Z 300IP Firmware

elationservice ·
Upload tool: C-Loader ZCL Bar Z 300IP Firmware V1.03 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture...
Topic

Six Par Z19IP Fixture Firmware

elationservice ·
Upload tool: C-Loader or USB Stick Six Par Z19IP Firmware V 1.07 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see...
Topic

DW Par Z19IP Fixture Firmware

elationservice ·
Upload tool: C-Loader or USB Stick DW Par Z19IP Firmware V1.06 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see...
Topic

CUEPIX Panel Firmware

elationservice ·
Necessary upload tool: CUE Software Uploader CUEPIX Panel Firmware V1.20 What's new: Changed the term Master/Slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do...
Topic

ACL Par 200 & 200IP Firmware

elationservice ·
Upload tool: C-Loader or USB Stick ACL Par 200 Firmware V1.08 ACL Par 200 IP Firmware V1.03 What's new: Changed menu text from Master/slave to Primary/Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and...
Reply

Re: Cuepix Series Fixture Firmware

elationservice ·
Split off CuePix Blinder WW2 and WW4 into their own thread with newer updated firmware: See here
Reply

Re: Cuepix Series Fixture Firmware

elationservice ·
Updated firmware's and models August 2017.
Topic

Cuepix Series Fixture Firmware

elationservice ·
Cuepix Batten Fixture Firmware V1.10 What's new: Improvements to the strobe timing. Cuepix Panel V1.18 What's new: Improved RDM information when using on a MA2 controller the RDM light will also flash. (More Cuepix series firmware coming soon) You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader...
Topic

Gigbar Move & Gigbar 2 Profiles

smundy ·
I've been trying to get the profiles for these 2 units. Can anyone help?
Topic

Protron Eclypse Firmware

elationservice ·
Firmware Tool Required: A-Loader (SNI211) Protron Eclypse Firmware V1.5 What's new: The flickering image on 16bit master channel Using duration and rate set at 255 in manual mode to get a steady output Use only 75% of max output power in manual mode. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software...
Topic

E Spot Series Fixture Firmware

elationservice ·
E Spot LED III Firmware V1.3.1 What's new in V1.3.1: change menu display to read Primary/Secondary instead of Master/slave. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your...
Topic

Volt Q5E Fixture Firmware

elationservice ·
Uses E-Loader uploader tool. Volt Q5E Firmware V1.0.4 What's New: Change menu text from Master/slave to Primary/Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your...
Topic

Protron 3K Color Firmware

elationservice ·
Uploader Tool Required: SNI Uploader Protron 3K Color Strobe Firmware V1.1 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact ...
Reply

Re: DTW Blinder 700IP Firmware

juan ·
Buenos días, mi pregunta, yo tengo los dtw 700ip y estan en la versión 1.0.5 por solo hay en la paguina la versión 1.0.4
Reply

Re: DTW Blinder 700IP Firmware

Ricardo C. ·
Firmware V1.06 is available for download. V1.06 esta disponible
Reply

Re: DTW Blinder 700IP Firmware

juan ·
muchas gracias
Reply

Re: DTW Blinder 700IP Firmware

juan ·
buenas tardes me paso algo muy raro estoy actualizando los dtw 700 solo me estan prendiendo un solo lente sera q me puedes colaborar con este problema
Reply

Re: DTW Blinder 700IP Firmware

Ricardo C. ·
¿Ocurrió el problema con todas tus luces, o solo unas pocas? ¿Estaba el problema presente antes de la actualización?
Reply

Re: DTW Blinder 700IP Firmware

juan ·
me pueden regalar la version 1.0.4 aver si puedo recuperar las targetas q no me estan funcionando
Reply

Re: DTW Blinder 700IP Firmware

Ricardo C. ·
Por favor envieme un correo electronico a ricardo.campos@elationlighting.com
Reply

Re: DTW Blinder 700IP Firmware

juan ·
Mi correo es tobondavid@hotmail.com
×
×
×
×