Tagged With "Panel"

I have had these Design Spot 250 lights for about 9 years and the rubberized coating on the plastic covers of the lights had deteriorated into a sticky oily mess. You couldnt touch the units you'd end up with hands full of a greasy glop. No spray solvent I tried would remove this stuff. Elation couldn't help me, they wanted to sell me new replacement covers. They couldn't even tell me what the coating was made of. Each time I touched the lights I had to run and wash my hands. My workers...

Thank you for the tip, I came to the forum today because I'm having the same issue on my older Platinum 5R beams and 5R spots. It's only on the head covers so far, but when we cleaned them this year, some came out with white splotches that were sticky, some looked like the entire cover was coming off the substance was sticky underneath. I am going to try your soaking method to see if I can restore these head covers.

I don't know what this substance is but in the 90s there were lots of electronic gear that was encased with this rubber coating because it gave the device a "tough" look. Years later we know now that stuff is no good; it decomposes over time and turns to greasy sticky tar. Elation techs say the company doesn't supply lights coated with this substance anymore; they use a different plastic panel supplier for their products now, and they were not willing to say what the substance was or offer...

Necessary upload tool: CUE Software Uploader CUEPIX Panel Firmware V1.20 What's new: Changed the term Master/Slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do...

Hello guys, unfortunately I have a problem with the Elation KL Panel RGBWCL. Once every while the light is flickering, mostly about every 15 minutes. It doesn't matter if it's wired or the signal comes wireless. Even after an update (to V1.10). Can someone help me with this? Thank you very much!

Just to get the message right, we have about 20 to 25 panels in our show, and the flickering is not always the same panel, but always another one...

I would look at your DMX runs and make sure: A) That you don't have too many DMX devices on one run B) that the DMX line is terminated at the end C) If you have a DMXcat or DMX tester, try sitting in a cue/look and seeing if the flicker finder notices anything. You can also view the DMX levels while you see the flicker and see if something is being sent that shouldn't.

Having the same problem. We have tested everything we can think of, and the flashing/flickering continues to get worse. Did you ever find a solution?

Hi everyone, anyone still having this issue if you can tell me what Lighting console is in use and also the software/firmware version the KL Panels are on that would help us a lot in trying to help you. Thanks!

ETC Ion XE 20 Eos Version 3.2.2.25 OS Version 10.22.02.01 Image Provisioning version: 10.22.02.01 Fixture Library Version 3.2.2.20, 21.Jun.2023 KL Panel Software Version 1.1.2 Also, we are unable to get the KL panels to talk to the board via sACN. We get no response when pinging the instruments, including when connecting an instrument directly to the board via ethernet. In some cases, when we connect them, they will flash white intermittently (between .5-2 seconds between flashes) and...

Uses C-Loader uploader tool. Paladin Panel Firmware V1.0.7 What's new: Fixed display code bug and resolved a RDM addressing issue. Power output optimized. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and...

Uploader Tool needed: C-Loader Or USB KL Panel XL IP V1.03 What's new: - RDM improved - Screen lock bug solved when encoders were used - All pcb's software versions now visible in the info display You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the...

I had a similar glitch with mine a while back. Tried updates, wired, and wireless—no luck. Turns out, it was interference messing things up. Moved some other gear around, and boom, problem solved.

Uploader Tool needed: C-Loader Or USB KL Panel XL V1.08 What's new: Resolved NO DMX Stand Alone Bug. 5 second LED fade up after power cycle implemented. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures.

Uploader Tool needed: C-Loader Or USB KL Panel Firmware V1.14 RELEASE NOTES: 1. Adding Color Tuning and Output Balance 2. Improved 'Self Test Mode' 3. Improved 6000K full output, 4. Improves the channel name/color macros. 5. Improves this point; Color Macros cannot be adjusted with the individual color channels. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your...

Finally got my Aria X2 Transceiver. Did some testing using LightKey, Enttec USB Pro, Aria X2, and Jolt Panel FX2. Here are the results: 1. 2.4GHz works but only if Channel is set to 00. I played around with different channels on both Aria and Jolt Panels and anything other than both set to 00 wouldn't work. 2. Sub Gig US doesn't work, no matter what channel it is set to. 3. Sub Gig EU doesn't work. 4. Any channel other than 00 doesn't work. 5. Mesh doesn't work. If Mesh is set to on, Aria X2...