Tagged With "Dimmer"

I've got a dozen older DP-DMX20L units that are sending noise back into the electrical system and ultimately showing up in the sound system. Goes quiet at 0, 50 & 100% and the closer to 25 & 75% the louder the hum. Is this simply inexpensive dimmers or should I be looking elsewhere? It should be noted that ALL audio signal cables are balanced XLR type, everything is powered from the same panel with the same ground (I know, I installed it.) I actually didn't have this issue when I...

Help! I just purchased four Cyber Pack 20a dimmers and can't understand the user manual at all! (what is a "note number"?) I am familiar with DMX and have used many different types of dimmers, but the documentation for this product leaves much to be desired. I'm wondering if anyone has seen more thorough documentation online that I can access. I'm trying to configure the units to work sequentially so the first pack is DMX 1-4, the next is 5-8, etc. What is the correct menu/button sequence to...

I have an SD1 that is working fine but I have recently purchased a couple of Optima Matrix Pro dimmer packs. THey are supposed to work in 1, 2, and 4 channel modes. They work in 1 and 2 channel modes but fail in 4 channel mode. I have contacted the seller but they have no answers. I have suggested several times that it may be my programming but they are not familiar with the SD1. I am creating it as a Generic Dimmer and assigning 4 channels to it. I have tried 4 different dimmer packs and...

Hi, After multiple tests using either of the Generic Dimmers definitions… I found that one definition is only 2 chnl and the other definition is 3 chnls. Instead of defining it as a Generic Dimmer pack I used RGBW and now I have all 4 channels working fine. Thanks, Phillip

Hi, this should all work fine, as long as the patch is correct and the packs themselves are in the correct mode and address, if it works in 1 and 2ch, it should work in 4ch.

Hi everybody! I am currently renovating a permanent install which was a mess. I have found two unknown Dmx 5 pin leads that look like they are home runs from the dimmers in the back to the console. I am having ghosting issues with these two Dmx lines they look like two separate lines. There is no problem with the console because there is only one dmx line that runs to the dimmers and they work perfectly. Do not know the brand of the dimmers. I am wondering what my next troubleshooting steps...

Hey, does anyone have an idea for what the problem might be ?, I tried to use different type of dc adaptores.

Hello, I know this thread is more of a general area, but we can't offer advice for gear that is not Elation or ADJ branded equipment, and this unit doesn't look to be one of our old SS 24s. I would find the manufacturer and email or call them.

Hello I am working with a local church regarding some new lighting and have a few questions. I am looking at the following lights: -Elation KL Fresnel 6 150W 3000K -Elation KL Fresnel 4 50W 3000K Four of the 6" Fresnels across the front. Two 4" Fresnels for backlighting the main speaker and another two 4" Fresnel for additional lighting. My main question regards controlling theses lights. The church uses the following for lighting control: -ADJ DP-DMX20L 4 channel Dimmer Packs (qty4) -Stage...

Thank you for your response. So, just to be clear. Fixtures need to plug straight into AC with the powerCON/Edison adapter. DMX just daisy chains through the lighting fixtures. DMX addresses each fixture directly. Correct?

That sounds correct to me, yes.

Hi, these KL series of fixtures cannot be run off of a dimmer pack, or at least the ones you mentioned cannot. they need their own power source that is outside of the edison plugs on the DP-DMX20L. and they will have to be wired into DMX in the chain as new fixtures.

Hello, It Looks you're experiencing electrical interference issues in your lighting system, affecting your sound system. This is likely due to inexpensive or older dimmers. The noise is most noticeable at specific dimming levels and disappears at 0%, 50% , and 100%. To resolve the problem: Consider dimmer quality and upgrade if necessary. Ensure you're not overloading dimmers with excessive wattage. Physically separate dimmers from audio equipment. Verify proper grounding to prevent ground...

I have a bunch of old Platinum Spot LED Pro II fixtures that I am trying to fix up, a number of them have similar issues and a couple of them have unique issues. I will detail below, and if anyone on here can assist, that would be amazing. Dimmer Issue: A couple of differing issues here. First issue, the dimmer PCB will not output any voltage the LED, but when putting the dimmer into a working fixture, the dimmer outputs perfectly fine, its as if something within the faulty fixture is...

Hi, if you email our service team we can try to assist you with this, please email service@elationlighting.com Thanks!