Tagged With "pro"
Topic
5R Spot Pro cyan, yellow, magenta color error
5R spot pro with a cyan yellow and magenta color error tried replacing the CMY unit with a know working one to no avail. Any thoughts?
Topic
Using MIDI with Alcorn McBride WinScript
I'm designing a 4D simulation using an Alcorn McBride V16 Pro as the base controller. For the lights, the V16 has MIDI out which I'm sending to an SD2 lighting board. The issue is that the MIDI format is different than standard MIDI. Does anyone know any workarounds for this? Particularly if you've had experience using WinScript to program MIDI cues. I don't know if there is a way for the MIDI message to automatically convert to Elation's format or if there is a specific I/O or variable I...
Topic
SD1 and Generic Dimmer pack programming
I have an SD1 that is working fine but I have recently purchased a couple of Optima Matrix Pro dimmer packs. THey are supposed to work in 1, 2, and 4 channel modes. They work in 1 and 2 channel modes but fail in 4 channel mode. I have contacted the seller but they have no answers. I have suggested several times that it may be my programming but they are not familiar with the SD1. I am creating it as a Generic Dimmer and assigning 4 channels to it. I have tried 4 different dimmer packs and...
Reply
Re: 5R Spot Pro cyan, yellow, magenta color error
greetings, you may have a bad pcb. Please remove the arm covers and inspect the Caps for swelling.. if ok try exchanging IC HY483n-3U01
Reply
Re: Using MIDI with Alcorn McBride WinScript
Good morning, i will refer this one to our show designer engineer Ken. it may take a day or so, just an fyi
Reply
Re: Using MIDI with Alcorn McBride WinScript
The SD2 uses standard MIDI continuous controller messages to trigger scenes. As long as you can generate those from you software you should be able to create cues. The SD2 manual has a page that shows how to make the message. Controller messages work better than notes for this controller due to the large number of scene slots.
Reply
Re: SD1 and Generic Dimmer pack programming
Hi, After multiple tests using either of the Generic Dimmers definitions… I found that one definition is only 2 chnl and the other definition is 3 chnls. Instead of defining it as a Generic Dimmer pack I used RGBW and now I have all 4 channels working fine. Thanks, Phillip
Reply
Re: SD1 and Generic Dimmer pack programming
Hi, this should all work fine, as long as the patch is correct and the packs themselves are in the correct mode and address, if it works in 1 and 2ch, it should work in 4ch.
Topic
eNode 8 PRO Firmware (VERSION 2 ONLY)
Upload Tool: SNI Software Uploader eNode 8 PRO V2.6 firmware (VERSION 2 ONLY) THIS FIRMWARE IS FOR ENODE 8 PRO VERSION 2 UNITS ONLY! If you are not sure, contact us at the email listed below. Release notes: Devices should not do a full broadcast to 255.255.255.255, but rather to 2.255.255.255 RDM Support. Instructions for uploading Enodes You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture...
Topic
eNode 8 PRO Firmware (VERSION 1 ONLY)
Upload Tool: SNI Software Uploader eNode 8 PRO V1.12 firmware (VERSION 1 ONLY!) THIS FIRMWARE IS FOR ENODE 8 PRO VERSION 1 UNITS ONLY! If you are not sure, contact us at the email listed below. Release notes: Devices should not do a full broadcast to 255.255.255.255, but rather to 2.255.255.255 RDM Support. Instructions for uploading Enodes You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant...
Topic
Dr PRO Rack Rack Firmware
DR PRO Rack Firmware V1.41 Please see below for software and instruction on how to update the unit. New software fixes the following bug, when going into the Set Date/Time under User Set, the year doesn't go past 2020. 1-Press and hold Right and Enter button, power on the device all Leds will flash once. 2-Connect the device with PC via usb cable, the unit will be recognized as RamBootLoad(E/F:). 3-Drag the file to RamBootLoad(E/F:) and unit will automatically update itself. Any questions or...
Reply
Re: Platinum spot 5r pro missing fan menu
Greetings, fan control was removed, the 5r Lamped required a fixed air flow (unlike traditional discharge lamps) meaning speed could be be variable.
Topic
Platinum spot 5r pro missing fan menu
Hello everyone. Today I was using the V1.0 Plat Spot 5R Pro menu to help me find the fan control. According to the manual it is in the personality menu and between Status Settings and Display Settings. On my fixture which is running V1.1 there is no such menu. I can not find a V1.1 menu anywhere online and I have gone through the menu on the head and can not find anything to do with Fan control. Can anyone help?
Reply
Re: Design Spot 250 Pro Service Manual needed
Greetings, please email me at gines dot gines at elation lighting dot com. also just a heads up parts for the DS250pro are no longer available. also let me know what issues you are having, i maybe able to point you in the right direction.
Topic
Design Spot 250 Pro Service Manual needed
A bit of a shot in the dark but decided to ask here... In the past (2011 or so), requests for service manuals would usually get a response of "Send me your email and I'll forward one to you". Is that still possible today? I have two 250 Pros I need to revive for my church. (I already downloaded the User Manual...) Any help is greatly appreciated!!
Topic
Satura Led Spot Pro v2 Standard - suddenly fading out/in
Hi Guys. Any ideas on what is the problem with Satura Led Spot Pro v2 Standard fixture that is constantly fading out & in during operation? Is it the module problem or power supply? Do I need to replace parts for this issue? Any inputs and advise are highly appreciated. Thank you
Reply
Re: Satura Led Spot Pro v2 Standard - suddenly fading out/in
Greetings, this can happen due to overheating, check the fans @the led engine and insure they are rotating properly and to speed.