Tagged With "V1.13"
Reply
Re: Basics of Compu Live 06
Ok I have added the 8 fixtures I think there may be a problem with the dmx protocol's the coemar manual shows them as a 13 channel fixture while the ssl file shows it as a 6 channel fixture?
Reply
Re: Help setting up lights... total noob
Ok... after reading through the forum (which is awesome) last night for a couple of hours I think I figured it out... 1. Set the first DP-415 to read channel 1 2. Set the second DP-415 to start reading at channel 5 3. Set the first group (Back wash) of Color Wash light to read channel 9 (Master/Slave mode) 4. Set the second group (Back lights) of Color Wash lights to read channel 13 (Also Master/Slave mode) Is this right? Am I even close?
Reply
Re: Newbie w/ Scene Setter 24
Mattrix, You'll need to create your own programs to limit the number of channels/lights being used. Here's how to program a chase. 1) Change the mode to "1-24 single" 2) Enter record mode (press and hold record button and tap buttons 1,6,6,8) 3) Create the first step of your chase using sliders 1-12. Press the record button and the display should then read step 001. Create as many steps as you need to complete your desired pattern. The controller will continue to display the number of steps...
Reply
Re: stage setter 8 problems
Depending on the units in question, they might have a sound active setting via DMX. Look in the manuals/DMX charts for them. If confused, list the fixtures for us and hopefully we can help more. Little side story with regards to dimmers and things other then filament lights plugged into them. A local company rented a school 13 Mac 700s in my area not to long ago. This is all fine and dandy, but the school in question I use to work at and know it doesn't have the power for 13 Mac 700s. So I...
Reply
Re: Tri-Op Colors
what's a Tri-Op? Opti Tri Par? check out pages 10-13 of the user manual. I think you will see it has all you are asking about. http://www.elationlighting.com...les/opti_tri_par.pdf
Reply
Re: Lumi LED-100 Profiles
13 channel fixture? I believe i have it. check your email in a bit. Sincerely,
Reply
Re: another noob question.....
Sergio, I have an Scene Setter 24 ch connected to two ETC Smartpack wall mounted dimmer panels. SS24 outputs 1-12 go to 1st panel with 12 dimmers and outputs 13-18 to second panel with 6 dimmers. The SS24 outputs are in sequence but actual light wiring to dimmers is mixed. How can I assign sliders to match the phisical light configuration (as suggested in your remarks)? Or do I need to rewire the dimmer panels to match SS24 sliders? Johnhrv The existing
Reply
Re: another noob question.....
Sergio, Thanks for your reply. I am not at our church to check the DIPs but all 18 outputs are working now using DMX. No the slider channels have not been changed. BUT, that is what I want to try but cannot find instructions. Can you direct me to a source of instruction for changing slider output channels. My other option is to re-wire the ETC Smartpacks. My objective is to get the SS24 sliders in the same order as theater lighting fixtures (now mixed). johnhrv
Reply
Re: Buggy MAC version
Any word of an update yet? Noticed that the developers have posted build 13.
Reply
Re: Buggy MAC version
Still no upgrade yet? It's nearly two weeks since C***** posted the upgrade to build 13 !!!!
Reply
Re: Buggy MAC version
OK, ten seconds of testing reveals (as I stated two weeks ago above) when you start program, FOG-STROBE-BLINDER buttons are latched ON. This was in C***** Build.13 as well and reported to them. still not fixed in Build.14 Will look at more after I put little one to bed.
Reply
Re: Addressing cans on Compuware
It sounds like your addressing is off. Compu live software will auto patch for you however you need to make sure that your fixtures addresses match what is on the software. So when you are patching say 4 moving heads and you want them to start at 11 and you have 4 of them you need to tell the software starting address is 11 and number of fixtures is 4. As far as checking your addresses here is the best way. find your "Pages" tab as shown in the picture. I have circled in red all the starting...
Reply
Re: Buggy MAC version
It is updated now, still shows B.14 when I think it is only b.13 Auto update still does not work. Strobe etc. do not latch now but still crashes. Really not too impressed....
Reply
Re: DMX Operator 192 - software
OK I have downloaded the software although I haven't yet hooked up my Operator 192. I am just trying it in demo mode. The light pars that I have are new, they are by Microh, you can't even see them on the website, although there is a similar system that is exactly like mine except different pars. I have checked the online manual for the system that they have online and it is exactly the same and works the same way. The system is the LED Quadpar. It consists of 4 pars on a single tree. The...
Reply
Re: DMX profile for Design Spot 575B
Jwyman, the profile I think you are looking for is already in the Ion: The "Design Spot 575E 8B" is the 8 bit (22 channels) of the Design Spot 575E and the "Design Spot 575E 16B" is the 16 bit (24 channels). The Design Spot 575B or Basic does not have any profiles in the Eos, Ion, and/or Element for the 8 bit (13 channels), 16 bit (15 channels) or 16 bit Extended (24 channels).
Reply
Re: help with building a matrix
OK Here goes. As of the last beta of CompuShow I tested, the profile editor still did not allow for a fixture to have multiple R, G, or B slots. Therefor, you can patch a matrix with the full profile but the effects will only work for pixel 1. (Very few console manufacturers have this capability built in to their consoles as of yet.) Build a Matrix of 3 Channel RGB Units. It can be handy to open a 3 channel LED fixture profile in the PROFILE EDITOR and name it Pixel and save it as Pixel.
Reply
Re: Stage Pak 1
Well, to start with, we have the Stage Setter 8 controller, which is nothing more than a 16 channel DMX controller. Then you have 2 DP415 dimmer packs, which are both 4 channel dimmer packs. Starting in with your Roller Trons, I'm assuming perhaps incorrectly that you have the Roller Tron 250's. But I could be wrong. These are 5-channel DMX fixtures. Channel 3 and Channel 4, value 255, is SOUND ACTIVE. So these support SOUND active, probably in a "per mode" bass. Channel 3 being sound active...
Reply
Re: Profile for Chauvet Qwash 260 LED
Hey im sorry i meant i needed the 13 channel profile, that one is for the 9 channel mode
Reply
Re: Profile needed for American DJ Vizi LED Spot
Ken, I downloaded the profile and took a look at it in the fixture editor and noticed the profile and the channel listing in the manual don't match up. They differ as follows... Chan. Vizi Spot Manual - Profile (from elation website) 1 Pan Movement 8bit - Pan Movement 8bit 2 Pan Movement Fine - Pan Movement Fine 3 Tilt Movement 8bit - Tilt Movement 8bit 4 Tilt Movement Fine - Tilt Movement Fine 5 Color Wheel - Color Wheel 6 Gobos - Gobos 7 Gobos Idx/Rot - Gobos Idx/Rot 8 Rot Prsm/Gobo Macro...
Reply
Re: Why can't I get the profiles from the web library
Thanks a lot! So far it looks like everything I need. The 14 channel minspot (13 and 6 were easy to come by), scorpion storm rg, and others all seem to be there. I will check out the compu show later I do t have my lap top on me. I would really like to use it I hope I can get it to work. I did load it on my home pc also to make sure it wasn't a problem with the laptop but it does the same thing. Anyway, thanks again for your help, it is very appreciated!
Reply
Re: Release one playback button when another one is fired
Download the latest manual and look at page 13. That has the info on bundles.
Reply
Re: Lamp on using the DMX Operator Pro
Nuts, I don't have the magic, I have the Operator Pro. I may have posted in the wrong forum, saw DMX operators and thought it also included operator pro. But I did find what you are talking about, though I swear there is new information each time I look at the manual. I now see the lamp on command under the last channel, in my case 13. Thanks for your patience. I do have trouble seeing things that are right in front of me sometimes.
Reply
Re: Lamp on using the DMX Operator Pro
oh no this is the right forum. lol I saw magic 260 first and assumed it was for that. It's forthe Op PRO. got it. but ya channel l13 has the commands for lamp on and off and even color split enable etc. But ya put channel 13 in the Color change to any position value and then move the fader for the color wheel and you will get fine control of that. Also for color and gobo to any position this is usefull if you want the gobo channel to slowly fade from one gobo to the next without snapping.
Reply
Re: SceneSetter 24 DMX assign mode not working
I'm not sure what brand the dimmers are, but they are 12 channel. The start address of the one that does house lights is 1, the stage light dimmer starts at 13. I've sent you an email.
Reply
Re: design wash led 60
They appear to be the same. The profile is for the default 13 channel mode.
Reply
Re: profileneed...
13 channel mode: https://www.dropbox.com/s/0i81...inum%20Beam%205R.ssl Sincerely,
Reply
Re: Profile needed
Is this what you need ? Or you need the manual? How can I send you the manual ? It can also be used in 24 channels too. 1-Pan 2-Tilt 3-Speed 4-Lamp on at 130.139 5-Colors 6-Nothing 7-Gobos 8-Rotacion Color wheel 9-Rotation Gobo Wheel. Fine set up 10-Prism 11-Rotacion Prism . Fine set up 12-Frost 65.255 Cierra el open gobo 13-Zoom 14-Focus 15-Strobe 16-Dimmer.
Topic
New profile for SD3
How do I get a fixture profile for a new one I have. I have attached the user manual. I want to use the 16 channel set up.
Topic
Blizzard HOTBOX exa Profiles
Are there profiles available for the Blizzard Hotbox exa LED PAR for the Emulation controller? I am especially interested in the 10-channel version.
Topic
Spot Briteq BT-Theatre 60FC Black LED theaterspot
Spot Briteq BT-Theatre 60FC Black LED theaterspot I have got an demo. The spot Briteq BT-Theatre 60FC Black LED theaterspot is very good. We want to buy 10 of them but without fixture we can’t use them with Emulation. Can you do the job? If we have the fixture, how can we update Emulation with teh fixture, Best regards, Deschamps Koen.
Topic
DMX address in 2/8 or 2/12 mode for Chavet
For the Elations 8 and 24 Trendsetter DMX 2 (9 or 13) in 2/8, 8/8 or 2/12, 12/12 mode isn’t recognized by Chauvet's EVE E-50Z (either in channel 1 or 3 mode). In fact, it refuses to work on any DMX channel other than DMX1. With the 1/16 and 1/24 mode DMX for all channels work individually as addressed. Is the Elations Trendsetter putting out an address which it’s not publishing? The other devices work on DMX 9 or 13 when in 2/8, 8/8 or 2/12, 12/12 mode.
Topic
ZCL360i Fixture Firmware
Uses: C-Loader II ZCL360i Firmware V1.05 What's new: Improvements to RDM You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic
FuzeWash Z350 & Z120 Color Presets
We are currently using ShowXpress software so I am having to build my own profiles for all my new Elation lights. I am looking for a list of all the 64 Color Presets to properly name them, as well as the 13 Color Macros. I've searched on here as well as Google and haven't been able to locate the information. Thanks
Topic
Fuze Par Z60 Fixture Firmware
Firmware Tool Required: C-Loader II Fuze Par Z60 Firmware V1.06 What's new: See release notes included in the download. This update resolves intermittent flicker issues. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your...
Topic
ACL360i Firmware V1.1.3
Upload tool: CUE Software Uploader ACL360i Fixture Firmware V1.1.3 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic
WW Profile HP Fixture Firmware
Uploader Tool required: E-Loader WW Profile HP Firmware V1.1.5 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic
CW Profile HP Fixture Firmware
Uploader Tool required: E-Loader CW Profile HP Firmware V1.1.6 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic
DMX?
My church recently updated it's older Scene Setter 24 to the newest model. We are running cans on faders 1-12 and have 4 RGB LED lights that we run on faders 13-24. On the old board everything works great. With the new board the cans work but not the LEDs. I have tried to look for articles to learn how to modify the DMX for faders 13-24 on the new board but it's like hunting for the Ark of the Covenant. Is there a way to read the DMX setting for those faders on the old board and then modify...
Topic
Needing two profiles to add to Emulation software.
Needing profiles built for Chauvet Intimidator Spot 110 10 w and Blizzard Lighting Lazer Blade G. I have attached the manuals with the information. Any help would be greatly appriciated!
Topic
SixBar1000 issues
Howdy! I need some advice. (obviously)... I am installing 10 Sixbar 1000 fixtures on a 3rd universe in our theatre.... I have addressed them starting at dmx 3/301 and so on using them in the 13 channel mode. When I set dimmer to 100% and bring up any color combination, three of the Sixbars do not work correctly. Note, that when I change those fixtures to 7 channel mode with the same dimmer settings, they work correctly. Another note: If I change the DMX addressing to mimic another fixture...
Topic
origional show desighner 2 button problem
i was woundering if you can help me i have a origional show desighner 2 my button 13 is not working i was woundering would it be just easy to replace the whole board or just the button i have used the board for well over 6 years and never had a problem just with natural wear and tear was thinking it might be easier to replace the whole board ....what would be the cost of a new cuircut board.... and what would be the cost for a new button each thanks for your time bob hauck
Topic
Need profile please!!!
I just ordered some new lights but can't find a profile that works. Any help would be AMAZING!!!!! Info below 36X5W 180W LED MOVING HEAD WASH LIGHT Channel Function 1 Pan 2 Tilt 3 Pan/Tilt speed 4 Dimmer 5 Red 6 Green 7 Blue 8 White 9 Strobe 10 Color Change 11 Mixed Color 12 Auto Mixed Color 13 Pan Fine 14 Tilt Fine 15 Reset Thanks so much!!!!!!!
Topic
Transferring a user profile from one computer to the next does not work!
Hey guys, frustrating problem here... My friend and put a lot of work into a show profile on his computer, a 15 inch macbook, but it is no longer available to use for my shows... so I have tried to put the .xml file on my computer (a 13 inch macbook), and while it opens up just fine none of the programs work! I can still control my lights and program new stuff but I can't use any of the chases/cuelists we made on his! When I play something one of the chases, the numbers corresponding to the...
Topic
Scene Setter 24 Moron
I am a complete moron on the scene setter 24. I understand DMX addressing. I have a 4 channel dimmer at DMX1 I have another one at DMX5 I want sliders 1-4 to control the intensity of the first 4 lights Slider 508 the second set. I have a stage ape ape coaster at channel 13. I want 13-18 to control it. Right now I have no control of any light (it was working yesterday but I think I accidentally hosed something) I want to assign flash 1 and slider 1 to DMX1, flash 2, slider 2 to DMX2 etc... I...
Topic
mini wash chinese
Hi I have a few Chinese made Mini Wash's that I need a profile for they are 8 and 13 channel. 1. pan 2. pan fine 3. tilt 4. tilt fine 5 pan/tilt speed 6. dimmer and strobe 0-7 blank 8-134 dimmer 135-239 strobe from 0hz to 40hz 240-255 open 7. red 8. green 9. blue 10 white 11.color 0-7 blank 8-21 white 22-34 red 35-49 dark green 50-63 dark blue 64-77 light blue 78-91 magenta 92-105 yellow 11. 106-119 purple 120-134 orange 135-147 light green 148-161 pink 162-175 brown 176-189 gold 190-203...
Topic
iPhone Remote
I'm having issues connecting with the iPhone Rigger's Remote since updating to the new build. I've tried multiple wifi networks and multiple ports, nothing seems to work. Here are my specs: rMBP 13" Late 2013 OS X 10.11.3 iPhone 6S iOS 9.2.1 Emulation 1.3.94
Topic
Profile needed please
I got Compu pro 04 (Compu Live) and I need help with profile for some of my lights. I got Chinese made Beam Spot 280W. It runs on 16 and 24 channels . If you need the manual how can I send it to you ? Thanks in advance . 1-Pan 2-Tilt 3-Speed 4-Lamp on 130.139 5-Colors 6-Nothing 7-Gobos 8-Rotacion Color wheel 9-Rotation Gobo Wheel. Fine set up 10-Prism 11-Rotacion Prism . Fine set up 12-Frost 65.255 Cierra el open gobo 13-Zoom 14-Focus 15-Strobe 16-Dimmer.
Topic
Satura Series Fixture Firmware
Uses E-Loader uploader tool. Satura Profile Firmware V1.0.10 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic
Graphics on easyshow video timeline
Can anyone tell me an "economical" way to play static graphics on the Easy Show video Timeline? About 13 of my show is action video in AVI format... but the rest is just artwork or titles that I have been rendering as AVI files cut to the exact space length that they need to fit. My show is 80 minutes long so once I ge all the files lined up as AVI's.. the program starts to lag, which I beleive is due to the huge size of the AVI's. The graphic art is nothing more that a small jpeg stretched...
Topic
Mega-Lite SSL files
So I'm new to this SW but was wondering if there was a place to find the SSL files for some lights that aren't listed in the list. In particular I was looking for the following Mega-Lite N-E Color Strip LED (13 channels) Mega-Lite N-E Color Par LED (4 Channels) Thanks John