Skip to main content

Tagged With "Firmware V1.03"

Everything
Reply

Re: Global Edit of Values for One Light + Right Click to Fade

ebaclights ·
There is a way to do fade/no fade using the Midi controller. You can either do it with the virtual controller on the screen, or have an external one. Unfortunately you cannot use a single button to turn the fade on and off with the virtual board, you will have to use 2 buttons, or one of the faders on the board. You can use one button for On/off using the external board because it will latch when you press the button. To set this up... 1. launch the midi controller on the screen. 2. If you...
Reply

Re: Visualizer help

sasquatchproductions ·
Hey James, hope your holiday was good! Got to work a bit with the viz over break and everything is working well except for the colors on some the fixtures that i added in. Every color is coming up green, and I've tried using High End Trackspots v1 and high def profiles and am having the same problem. Not that it worries me with the viz, but im more concerned that i have the right profile foe the fixtures at the venue. Is this just a glitch or do you think I may have a problem? Thanks in...
Reply

Re: help with building a matrix

wheresjc ·
OK Here goes. As of the last beta of CompuShow I tested, the profile editor still did not allow for a fixture to have multiple R, G, or B slots. Therefor, you can patch a matrix with the full profile but the effects will only work for pixel 1. (Very few console manufacturers have this capability built in to their consoles as of yet.) Build a Matrix of 3 Channel RGB Units. It can be handy to open a 3 channel LED fixture profile in the PROFILE EDITOR and name it Pixel and save it as Pixel.
Reply

Re: need profile for High End Trackspot

dunn ·
v1 high resolution
Topic

ZCL360i Fixture Firmware

elationservice ·
Uses: C-Loader II ZCL360i Firmware V1.05 What's new: Improvements to RDM You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

Rayzor 360Z Fixture Firmware

elationservice ·
Uses E-Loader uploader tool. Rayzor 360Z Firmware V2.0.7 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

Paladin Panel Fixture Firmware

elationservice ·
Uses C-Loader uploader tool. Paladin Panel Firmware V1.02 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

Fuze Par Z60 Fixture Firmware

elationservice ·
Firmware Tool Required: C-Loader II Fuze Par Z60 Firmware V1.06 What's new: See release notes included in the download. This update resolves intermittent flicker issues. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your...
Topic

eNode 4 pre-sales support questions

Dave Nelson ·
I'm considering the purchase of an eNode 4 ArtNet-to-DMX output device. I have some questions. 1. There doesn't appear to be any firmware download available under the Support / Downloads link on the Elation home page. Why is that? 2. I found an article in the forum that referenced a firmware updater appliance (hardware product). Does the eNode 4 indeed require a specialized appliance to perform firmware updates? If not, where are the alternate instructions and firmware update files located?
Topic

ACL360i Firmware V1.1.3

elationservice ·
Upload tool: CUE Software Uploader ACL360i Fixture Firmware V1.1.3 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

WW Profile HP Fixture Firmware

elationservice ·
Uploader Tool required: E-Loader WW Profile HP Firmware V1.1.5 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

CW Profile HP Fixture Firmware

elationservice ·
Uploader Tool required: E-Loader CW Profile HP Firmware V1.1.6 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

Artiste Picasso Fixture Firmware

elationservice ·
Upload tool: None, fixture has a USB service port. Artiste Picasso Firmware V1.1.7 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact ...
Topic

Smarty Max Fixture Firmware

Jingles8302 ·
Upload tool: E-loader or fixture has a USB service port. Smarty Max Firmware V1.3.4 What's new: See release notes included in download. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not...
Topic

e spot led vs e spot led II

ljraph ·
Hi everyone Does anybody know the exact differences between V1 and V2? The led seems to be higher power 45W vs 60W, any other differences? Does anybody know if an upgrade kit will become available for V1? thank you Best regards Raphael
Topic

Rayzor Q7 & Q12 Zoom Fixture Firmware.

elationservice ·
Uses E-Loader uploader tool. Rayzor Q12 Zoom V1.1.6 Fixture Firmware What's new in V1.1.6: Enhanced Zoom calibration on the fixture menu display and added ability to do fixture reset on DC display power (battery powered) Rayzor Q7 V1.2.3 Fixture Firmware What's new: Fixed a slow movement bug in the software. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your...
Topic

Satura Series Fixture Firmware

elationservice ·
Uses E-Loader uploader tool. Satura Profile Firmware V1.0.10 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

Compu Live Not Responding

nhnaz ·
I purchased Compu 1024EC and installed Compu Live (03-21-2008) on a Compaq Laptop running Vista Home Premium (32 bit). On My first attempt, I installed the demo pages and started in beginner mode as the manual suggests. When I attempted to add my own Elation Cyber Pak Dimmer the software stopped responding. I was following the instructions for adding your own fixtures using the scan library. The fixture test in step 3 worked and I got through to the last step. When I clicked on the Finish...
Topic

Easy Show timeline not scrolling

nhnaz ·
I am having problems with Easy Show using the 11/08 version. The timeline will not scroll correctly when playing back a show using an mp3 file. You never know when one frame ends if it is going to move to the next frame in the timeline or not. At first I thought it must be that my machine isn't powerful enough to keep up graphically. Then I thought maybe my antivirus software or some other process was slowing it down. After deleting stuff and trying on several laptops I was finally able to...
Topic

Trackspot profiles

italiatib2k3 ·
Is there an updated profile for High End's Trackspots? V1 somewhat works, but V2 does not. (I use the 2006 version of Compuware with the blue interface). With the V1 profile, the Color and Gobo features are all screwed up. For example, Gobo #2, 3, 4, and 5 are all color scrolls, albeit different speeds. Same deal with Color. There's also about 6 or 7 different strobes--which turns out to be different flash rates. Why not just use a single strobe icon with an adjustment slider?
Topic

Hello, Profile please.

tote ·
This is for a Marathon Quad Derby MA-523. Thanks 1 channel 0--127 motor Position 128--191 Positive infinite rotation, from slow to fast 192--255 Reverse infinite rotation, from slow to fast 2 channel 1...255 Flash frequently from slow to fast 3 Channel 1...255 Red lasting lighted, from dark to bright 4 Channel 1...255 Green lasting lighted, from dark to bright 5 Channel 1...255 Blue lasting lighted, from dark to bright 6 channel 0--10 The effect from Ch1 to Ch5 11--33 AU 01 34--57 AU 02...
Topic

Design Brick 70 II

wbrown ·
Just received our order of the new Design Brick 70 II. The DMX modes in the manual don't match the modes on the fixture. Through trial and error I've figured out: Color control - 5 CH MODE (DEFAULT) Color prog - 8 CH MODE Color_Saturation Hue Intensity CT - 4 CH MODE Color prog. Hue Saturation CT - 11 CH MODE Group Control - 35 CH MODE My questions, What is Pixel Grouping, and how does it work? I have a remote that we bought with our Design Bricks v1, will they work with the II (v2)? Thanks
Topic

Need OMEZ Lighting/ HTL Emulation Personalities for various fixtures

jcastld ·
Hey Jingles, I have a couple of lights I need to make work for a showcase at SIR in LA and have never seen them around before...They are High Tech Lighting/OMEZ Lighting products. If you can do this over the weekend I'd super appreciate it man, posting models and manual links below: 1. HTL Tri Color 18 Waterproof (7CH): http://www.omezlighting.com/manual/OM136.pdf 2. HTL Tri Color 20 (7 CH): http://www.omezlighting.com/manual/OM137.pdf NOTE The DMX and CH values look the SAME as previous...
Topic

James Thomas Profile

d-lights28a ·
Jingles, Looking for a profile for an 11 channel James Thomas Pixal Par 44. http://www.pixelrange.com/pixe...ixelPar44-v1-58b.pdf Its the 11 channel 4+E option on the channel assignments part of the pdf. Need it for tonight if possible... Thanks, D
Topic

KAM Powerbar Profile

hobson ·
A profile for the KAM Powerbar is in the Compu Show library. But that profile does not have the functionality I need. The Powerbar is a bar with four RGB fixtures attached. With 15 channel DMX one can control Master Dim, Programs, Strobe (which affect all four fixtures) and the Red, Green and Blue of each of the four fixtures individually. The preset in the library allows me to control Master Dim, Programs and Strobe, but, as best I can tell, whatever RGB combination is picked applies to all...
Reply

Re: ALright Elation Guys I need your Help with this

luisramirez ·
Ive Been Using Elation Products since 03'.Started out with 26 powerspot/power wash 250's, Now i Have the new design spot 575's 12 of them and 6 power wash 575's, Did major tours with American Idol, Tigres Del Norte, Vince Neil Of Motley Crue, and so many other artists, That prefer Elation over Martin or High End. Dont get me wrong here, High end And martin Are great Brands, But why Pay So Much For So little. Elation's Lights offer so much more for your money. I would Stick to Elation Great...
Reply

Re: External MIDI Trigger for BMP Rate

elationpro ·
Matchless.. see if you can wrap your head around this. 1. create scenes or switches with 1 color each 2. create cycle with each of the colors 3. change the time for each scene/switch to GO inside the cycle 4. now when you click PAGE-DOWN on your keyboard, you control the timing of the cycle 5. to assign this PAGE-DOWN control to MIDI, open the CONSOLE window 6. right-click on the MIDI controller button that you want to use (any button will work) 7. you will see a blank area with 4 icons to...
Reply

Re: Lamp start Design Spot 250 Pro

bdunard ·
I have been changing the delay number from 01 to 03 and it always seems to come on within about 20 seconds after I hit "lamp strike" in Compu. Do the number in the delay refer to minutes? If so, is there something else that I might not have set right that causes the lamp to strike at the same time no matter what delay time I have set.
Reply

Re: Lamp start Design Spot 250 Pro

Jingles8302 ·
Is the 01- 03 on the fixture itself or is that your time in compu? Sincerely,
Reply

Re: How does everyone organize their scenes/switches/etc

davidpatton ·
thanks for the reply that's pretty much the direction I've been heading, as far as grouping compressed buttons for a song; there has to be an intent from Elation when this was designed, as far as how to group scene/switch for songs; James, do you know this??? as to the ordering, it goes a character at a time, so everything with a '1' in the first character get's grouped, then everything with a '2', and so forth; then the second character comes into play, so '1' then '10' then '11' etc to get...
Reply

Re: Future for 64bit?

bobc ·
James, On 16 October 2009 11:18 AM, within this thread I posted "Please don't tell me that my investment 10 months ago in a 1024 is now obsolete. I would find that decision to abandon existing users quite damaging to Elation's trusted relationship with existing and future customers." You responded on 16 October 2009 03:43 PM, "We will not be abandoning you." I respectfully request that Elation revisit this decision. If not, I am going need more information and an acknowledment that in fact...
Reply

Re: Need help with compuware

mikepro ·
Does anyone out there know what kind of device i can get to hook up this to make it work. I am using the following a toshiba laptop to run the compuware software. My video system is the numark avm01 mixer dvd 01 dual deck and avm 03 screens. i run my sound into my regular dj mixer which depending on which rig i go out with it could be the dennon dnx900 or the rane ttm57sl. so what i do is run the master from the avm01 out to one of these mixers to play the audio from the dvd that is playing...
Reply

Re: Design Brick 70 II

elationpro ·
all good questions.. will investigate.
Reply

Re: Satura Series Fixture Firmware

elationservice ·
Updated August 9th 2019 with new release.
Reply

Re: Satura Series Fixture Firmware

elationservice ·
Updated original post Nov. 11th, 2019 with V1.0.10
Topic

Rayzor 760 Firmware Updates

elationservice ·
Uploader Tool Required: E-Loader Rayzor 760 Firmware V1.1.3 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Reply

Re: Problem with eNode 8 Pro / sACN and ETC Gio Lighting Desk

Jingles8302 ·
Hi you need to update the Enode 8 PRO to firmware 2.8, attached is the user manual. you may need to email firmware@elationlighting.com to get the firmware.
Reply

Re: SixBar 500 Firmware

elationservice ·
UPDATED LINK TO NEWEST FIRMWARE.
Reply

Re: SixBar 500 Firmware

Youri Gidding ·
any release notes or list of changes available?
Topic

SixBar 500 Firmware

elationservice ·
Uploader Tool Needed: C-Loader SixBar 500 Firmware V1.15 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

ACL Bar 360 Fixture Firmware

elationservice ·
Upload tool: CUE Software Uploader ACL Bar 360 Fixture Firmware V1.28 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

DTW Bar 1000 Fixture Firmware

elationservice ·
Necessary upload tool: CUE Software Uploader DTW Bar 1000 Firmware V1.13 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

Fuze Wash Z350 Fixture Firmware

elationservice ·
Firmware Tool Required: C-Loader II Fuze Wash Z350 Firmware V2.1.11 You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture listed, please contact Firmware@elationlighting.com
Topic

Fuze Par Z60IP Firmware V1.07

elationservice ·
Firmware Tool Required: C-Loader II Fuze Par Z60IP FW V1.07 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your...
Topic

ZCL Bar Z 300IP Firmware

elationservice ·
Upload tool: C-Loader ZCL Bar Z 300IP Firmware V1.03 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your fixture...
Topic

Six Par Z19IP Fixture Firmware

elationservice ·
Upload tool: C-Loader or USB Stick Six Par Z19IP Firmware V 1.07 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see...
Topic

DW Par Z19IP Fixture Firmware

elationservice ·
Upload tool: C-Loader or USB Stick DW Par Z19IP Firmware V1.06 What's new: Changed the term Master/slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see...
Topic

CUEPIX Panel Firmware

elationservice ·
Necessary upload tool: CUE Software Uploader CUEPIX Panel Firmware V1.20 What's new: Changed the term Master/Slave to Primary and Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do...
Topic

Dartz 360 firmware Updates

elationservice ·
Upload tool: C-Loader Software Uploader Dartz 360 Firmware V1.2.17 What's New: Changed menu wording from Master/slave to Primary/Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do...
Topic

Paladin Cube Fixture Firmware

elationservice ·
Uses C-Loader uploader tool. Paladin Cube Firmware V1.04 What's New: changed menu wording from Master/Slave to Primary/Secondary. You should not attempt uploading the firmware to the fixture unless you have read and fully understand the instructions that came with the relevant Fixture firmware uploader for your fixture. Clicking this link will take you to the Software uploader section of our website so you can pick the correct uploader tool for your needs and fixtures. If you do not see your...
 
Post
×
×
×
×